This is a purely informative rendering of an RFC that includes verified errata. This rendering may not be used as a reference.

The following 'Verified' errata have been incorporated in this document: EID 873, EID 874
Network Working Group                                          P. Savola
Request for Comments: 3964                                     CSC/FUNET
Category: Informational                                         C. Patel
                                                       All Play, No Work
                                                           December 2004


                    Security Considerations for 6to4

Status of this Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2004).

Abstract

   The IPv6 interim mechanism 6to4 (RFC3056) uses automatic
   IPv6-over-IPv4 tunneling to interconnect IPv6 networks.  The
   architecture includes 6to4 routers and 6to4 relay routers, which
   accept and decapsulate IPv4 protocol-41 ("IPv6-in-IPv4") traffic from
   any node in the IPv4 internet.  This characteristic enables a number
   of security threats, mainly Denial of Service.  It also makes it
   easier for nodes to spoof IPv6 addresses.  This document discusses
   these issues in more detail and suggests enhancements to alleviate
   the problems.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Different 6to4 Forwarding Scenarios  . . . . . . . . . . . . .  4
       2.1.  From 6to4 to 6to4  . . . . . . . . . . . . . . . . . . .  4
       2.2.  From Native to 6to4  . . . . . . . . . . . . . . . . . .  5
       2.3.  From 6to4 to Native  . . . . . . . . . . . . . . . . . .  5
       2.4.  Other Models . . . . . . . . . . . . . . . . . . . . . .  6
             2.4.1.  BGP between 6to4 Routers and Relays  . . . . . .  6
             2.4.2.  6to4 as an Optimization Method . . . . . . . . .  7
             2.4.3.  6to4 as Tunnel End-Point Addressing Mechanism . . 8
   3.  Functionalities of 6to4 Network Components . . . . . . . . . .  9
       3.1.  6to4 Routers . . . . . . . . . . . . . . . . . . . . . .  9
       3.2.  6to4 Relay Routers . . . . . . . . . . . . . . . . . . . 10
   4.  Threat Analysis  . . . . . . . . . . . . . . . . . . . . . . . 11
       4.1.  Attacks on 6to4 Networks . . . . . . . . . . . . . . . . 12
             4.1.1.  Attacks with ND Messages . . . . . . . . . . . . 13
             4.1.2.  Spoofing Traffic to 6to4 Nodes . . . . . . . . . 14
             4.1.3.  Reflecting Traffic to 6to4 Nodes . . . . . . . . 17
             4.1.4.  Local IPv4 Broadcast Attack  . . . . . . . . . . 19
       4.2.  Attacks on Native IPv6 Internet  . . . . . . . . . . . . 20
             4.2.1.  Attacks with ND Messages . . . . . . . . . . . . 21
             4.2.2.  Spoofing Traffic to Native IPv6 Nodes. . . . . . 21
             4.2.3.  Reflecting Traffic to Native IPv6 Nodes  . . . . 23
             4.2.4.  Local IPv4 Broadcast Attack  . . . . . . . . . . 24
             4.2.5.  Theft of Service . . . . . . . . . . . . . . . . 25
             4.2.6.  Relay Operators Seen as Source of Abuse  . . . . 26
       4.3.  Attacks on IPv4 Internet . . . . . . . . . . . . . . . . 28
       4.4.  Summary of the Attacks . . . . . . . . . . . . . . . . . 28
   5.  Implementing Proper Security Checks in 6to4  . . . . . . . . . 30
       5.1.  Encapsulating IPv6 into IPv4 . . . . . . . . . . . . . . 31
       5.2.  Decapsulating IPv4 into IPv6 . . . . . . . . . . . . . . 31
       5.3.  IPv4 and IPv6 Sanity Checks  . . . . . . . . . . . . . . 32
             5.3.1.  IPv4 . . . . . . . . . . . . . . . . . . . . . . 32
             5.3.2.  IPv6 . . . . . . . . . . . . . . . . . . . . . . 33
             5.3.3.  Optional Ingress Filtering . . . . . . . . . . . 33
             5.3.4.  Notes about the Checks . . . . . . . . . . . . . 33
   6.  Issues in 6to4 Implementation and Use  . . . . . . . . . . . . 34
       6.1.  Implementation Considerations with Automatic Tunnels . . 34
       6.2.  A Different Model for 6to4 Deployment  . . . . . . . . . 35
   7.  Security Considerations  . . . . . . . . . . . . . . . . . . . 36
   8.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 36
   9.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 37
   A.  Some Trivial Attack Scenarios Outlined . . . . . . . . . . . . 39
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 40
   Full Copyright Statement . . . . . . . . . . . . . . . . . . . . . 41

1.  Introduction

   The IPv6 interim mechanism "6to4" [1] specifies automatic
   IPv6-over-IPv4 tunneling to interconnect isolated IPv6 clouds by
   embedding the tunnel IPv4 address in the IPv6 6to4 prefix.

   Two characteristics of the 6to4 mechanism introduce most of the
   security considerations:

   1.  All 6to4 routers must accept and decapsulate IPv4 packets from
       every other 6to4 router, and from 6to4 relays.

   2.  6to4 relay routers must accept traffic from any native IPv6 node.

   As the 6to4 router must accept traffic from any other 6to4 router or
   relay, a certain requirement for trust is implied, and there are no
   strict constraints on what the IPv6 packet may contain.  Thus,
   addresses within the IPv4 and IPv6 headers may be spoofed, and this
   leads to various types of threats, including different flavors of
   Denial of Service attacks.

   The 6to4 specification outlined a few security considerations and
   rules but was ambiguous as to their exact requirement level.
   Moreover, the description of the considerations was rather short, and
   some of them have proven difficult to understand or impossible to
   implement.

   This document analyzes the 6to4 security issues in more detail and
   outlines some enhancements and caveats.

   Sections 2 and 3 are more or less introductory, rehashing how 6to4 is
   used today based on the 6to4 specification, so that it is easier to
   understand how security could be affected.  Section 4 provides a
   threat analysis for implementations that already implement most of
   the security checks.  Section 5 describes the optimal
   decapsulation/encapsulation rules for 6to4 implementations, and
   Section 6 provides further discussion on a few issues that have
   proven difficult to implement.  Appendix A outlines a few possible
   trivial attack scenarios in which very little or no security has been
   implemented.

   For the sake of simplicity, in this document, the native Internet is
   assumed to encompass IPv6 networks formed by using other transition
   mechanisms (e.g., RFC 2893 [4]), as these mechanisms cannot talk
   directly to the 6to4 network.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in BCP 14, RFC 2119 [2].

   Throughout this memo, IPv4 addresses from blocks 7.0.0.0/24,
   8.0.0.0/24, and 9.0.0.0/24 are used for demonstrative purposes, to
   represent global IPv4 addresses that have no relation to each other.
   This approach was chosen instead of just using addresses from
   192.0.2.0/24 [5] for two reasons: to use addresses whose 6to4 mapping
   is glaringly obvious, and to make it obvious that the IPv4 addresses
   of different 6to4 gateways need not have any relation to each other.

2.  Different 6to4 Forwarding Scenarios

   Note that when one communicates between 6to4 and native domains, the
   6to4 relays that will be used in the two directions are very likely
   different; routing is highly asymmetric.  Because of this, it is not
   feasible to limit relays from which 6to4 routers may accept traffic.

   The first three subsections introduce the most common forms of 6to4
   operation.  Other models are presented in the fourth subsection.

2.1.  From 6to4 to 6to4

   6to4 domains always exchange 6to4 traffic directly via IPv4
   tunneling; the endpoint address V4ADDR is derived from 6to4 prefix
   2002:V4ADDR::/48 of the destination.

    .--------.           _----_          .--------.
    |  6to4  |         _( IPv4 )_        |  6to4  |
    | router | <====> ( Internet ) <===> | router |
    '--------'         (_      _)        '--------'
        ^                '----'              ^
        |      Direct tunneling over IPv4    |
        V                                    V
    .--------.                           .-------.
    |  6to4  |                           |  6to4  |
    |  host  |                           |  host  |
    '--------'                           '--------'

                       Figure 1

   It is required that every 6to4 router consider every other 6to4
   router it wants to talk to be "on-link" (with IPv4 as the
   link-layer).

2.2.  From Native to 6to4

   When native domains send traffic to 6to4 prefix 2002:V4ADDR::/48, it
   will be routed to the topologically nearest advertising 6to4 relay
   (advertising route to 2002::/16).  The 6to4 relay will tunnel the
   traffic over IPv4 to the corresponding IPv4 address V4ADDR.

   Note that IPv4 address 9.0.0.1 here is just an example of a global
   IPv4 address, and it is assigned to the 6to4 router's
   pseudo-interface.

                                     Closest to
                                 "Native IPv6 node"
    .--------.       _----_        .------------.            .--------.
    | Native |     _( IPv6 )_      | 6to4 relay |  Tunneled  |  6to4  |
    | IPv6   | -> ( Internet ) --> | router     | =========> | router |
    | node   |     (_      _)      '------------'   9.0.0.1  '--------'
    '--------'       '----'  dst_v6=2002:0900:0001::1            |
                                                                 V
                                                             .-------.
                                                             |  6to4  |
                                                             |  host  |
                                                             '--------'

                                 Figure 2

2.3.  From 6to4 to Native

   6to4 domains send traffic to native domains by tunneling it over IPv4
   to their configured 6to4 relay router, or the closest one found by
   using 6to4 IPv4 Anycast [3].  The relay will decapsulate the packet
   and forward it to native IPv6 Internet, as would any other IPv6
   packet.

   Note that the destination IPv6 address in the packet is a non-6to4
   address and is assumed to be 2001:db8::1 in the example.

                                     Configured
                                        -or-
                                 found by IPv4 Anycast
    .--------.       _----_        .------------.            .--------.
    | Native |     _( IPv6 )_      | 6to4 relay |  Tunneled  |  6to4  |
    | Client | <- ( Internet ) <-- | router     | <========= | router |
    '--------'     (_      _)      '------------' 192.88.99.1'--------'
   2001:db8::1       '----'                     (or configured)   ^
                                                                  |
                                                             .-------.
                                                             |  6to4  |
                                                             | client |
                                                             '--------'

                                 Figure 3

2.4.  Other Models

   These are more or less special cases of 6to4 operations.  In later
   chapters, unless otherwise stated, only the most generally used
   models (above) will be considered.

2.4.1.  BGP between 6to4 Routers and Relays

   Section 5.2.2.2 in [1] presents a model where, instead of static
   configuration, BGP [6] is used between 6to4 relay routers and 6to4
   routers (for outgoing relay selection only).

   Going further than [1], if the 6to4 router established a BGP session
   between all the possible 6to4 relays and advertised its /48 prefix to
   them, the traffic from non-6to4 sites would always come from a
   "known" relay.  Alternatively, the 6to4 relays might advertise the
   more specific 6to4 routes between 6to4 relays.

   Both of these approaches are obviously infeasible due to scalability
   issues.

   Neither of these models are known to be used at the time of writing;
   this is probably because parties that need 6to4 are not able to run
   BGP, and because setting up these sessions would be much more work
   for relay operators.

2.4.2.  6to4 as an Optimization Method

   Some sites seem to use 6to4 as an IPv6 connectivity "optimization
   method"; that is, they also have non-6to4 addresses on their nodes
   and border routers but also employ 6to4 to reach 6to4 sites.

   This is typically done to be able to reach 6to4 destinations by
   direct tunneling without using relays at all.

   These sites also publish both 6to4 and non-6to4 addresses in DNS to
   affect inbound connections.  If the source host's default address
   selection [7] works properly, 6to4 sources will use 6to4 addresses to
   reach the site and non-6to4 nodes use non-6to4 addresses.  If this
   behavior of foreign nodes can be assumed, the security threats to
   such sites can be significantly simplified.

2.4.3.  6to4 as Tunnel End-Point Addressing Mechanism

   6to4 addresses can also be used only as an IPv6-in-IPv4 tunnel
   endpoint addressing and routing mechanism.

   An example of this is interconnecting 10 branch offices where nodes
   use non-6to4 addresses.  Only the offices' border routers need to be
   aware of 6to4, and use 6to4 addresses solely for addressing the
   tunnels between different branch offices.  An example is provided in
   the figure below.

    2001:db8:0:10::/60                   2001:db8:0:20::/60
       .--------.                           .--------.
      ( Branch 1 )                         ( Branch 2 )
       '--------'                           '--------'
           |                                     |
       .--------.           _----_          .--------.
       |  6to4  |         _( IPv4 )_        |  6to4  |
       | router | <====> ( Internet ) <===> | router |
       '--------'         (_      _)        '--------'
        9.0.0.1             '----'            8.0.0.2
                              ^^
                              ||
                              vv
                          .--------.
                          |  6to4  | 7.0.0.3
                          | router |
                          '--------'
                              |        2001:db8::/48
                        .-----------.
                       ( Main Office )
                        '-----------'
                              ^
                              |
                              v
                            _----_
                          _( IPv6 )_
                         ( Internet )
                          (_      _)
                            '----'

                                 Figure 4

   In the figure, the main office sets up two routes:

      2001:db8:0:10::/60 -> 2002:0900:0001::1

      2001:db8:0:20::/60 -> 2002:0800:0002::1

   And a branch office sets up two routes as well:

      2001:db8:0:20::/60 -> 2002:0800:0002::1

      default -> 2002:0700:0003::1

   Thus, the IPv4 Internet is treated as an NBMA link-layer for
   interconnecting 6to4-enabled sites; with explicit routes, 6to4
   addressing need not be used in routers other than the 6to4 edge
   routers.  However, note that if a branch office sends a packet to any
   6to4 destination, it will not go through the main office, as the 6to4
   2002::/16 route overrides the default route.

   This approach may make addressing and routing slightly easier in some
   circumstances.

3.  Functionalities of 6to4 Network Components

   This section summarizes the main functionalities of the 6to4 network
   components (6to4 routers, and 6to4 relays) and the security checks
   they must do.  The pseudo-code for the security checks is provided in
   Section 5.

   This section summarizes the main functions of the various components
   of a 6to4 network: 6to4 relay routers and 6to4 routers.  Refer to
   Section 1.1 of RFC 3056 [1] for 6to4-related definitions.

3.1.  6to4 Routers

   The 6to4 routers act as the border routers of a 6to4 domain.  It does
   not have a native global IPv6 address except in certain special
   cases.  Since the specification [1] uses the term "6to4 router", this
   memo does the same; however, note that in this definition, we also
   include a single host with a 6to4 pseudo-interface, which doesn't
   otherwise act as a router.  The main functions of the 6to4 router are
   as follows:

   o  Provide IPv6 connectivity to local clients and routers.

   o  Tunnel packets sent to foreign 6to4 addresses to the destination
      6to4 router using IPv4.

   o  Forward packets sent to locally configured 6to4 addresses to the
      6to4 network.

   o  Tunnel packets sent to non-6to4 addresses to the configured/
      closest-by-anycast 6to4 relay router.

   o  Decapsulate directly received IPv4 packets from foreign 6to4
      addresses.

   o  Decapsulate IPv4 packets received via the relay closest to the
      native IPv6 sources.  Note that it is not easily distinguishable
      whether the packet was received from a 6to4 relay router or from a
      spoofing third party.

   The 6to4 router should also perform security checks on traffic that
   it receives from other 6to4 relays, or 6to4 routers, or from within
   the 6to4 site.  These checks include the following:

   o  Disallow traffic that has private, broadcast or certain specific
      reserved IPv4 addresses (see Section 5.3.1 for details) in
      tunnels, or the matching 6to4 prefixes.

   o  Disallow traffic from 6to4 routers in which the IPv4 tunnel source
      address does not match the 6to4 prefix.  (Note that the
      pseudo-interface must pick the IPv4 address corresponding to the
      prefix when encapsulating, or problems may ensue, e.g., on
      multi-interface routers.)

   o  Disallow traffic in which the destination IPv6 address is not a
      global address; in particular, link-local addresses, mapped
      addresses, and such should not be used.

   o  Disallow traffic transmission to other 6to4 domains through 6to4
      relay router or via some third party 6to4 router.  (To avoid
      transmission to the relay router, the pseudo-interface prefix
      length must be configured correctly to /16.  Further, to avoid the
      traffic being discarded, 6to4 source addresses must always
      correspond to the IPv4 address encapsulating the traffic.)

   o  Discard traffic received from other 6to4 domains via a 6to4 relay
      router.

   o  Discard traffic received for prefixes other than one's own 6to4
      prefix(es).

3.2.  6to4 Relay Routers

   The 6to4 relay router acts as a relay between all 6to4 domains and
   native IPv6 networks; more specifically, it

   o  advertises the reachability of the 2002::/16 prefix to native IPv6
      routing, thus receiving traffic to all 6to4 addresses from the
      closest native IPv6 nodes,
   o  advertises (if RFC 3068 [3] is implemented) the reachability of
      IPv4 "6to4 relay anycast prefix" (192.88.99.0/24) to IPv4 routing,
      thus receiving some tunneled traffic to native IPv6 nodes from
      6to4 routers.

   o  decapsulates and forwards packets received from 6to4 addresses
      through tunneling, by using normal IPv6 routing, and

   o  tunnels packets received through normal IPv6 routing from native
      addresses that are destined for 2002::/16 to the corresponding
      6to4 router.

   The 6to4 relay should also perform security checks on traffic that it
   receives from 6to4 routers, or from native IPv6 nodes.  These checks
   are as follows:

   o  Disallow traffic that has private, broadcast, or certain specific
      reserved IPv4 addresses in tunnels, or in the matching 6to4
      prefixes.

   o  Disallow traffic from 6to4 routers in which the IPv4 tunnel source
      address does not match the 6to4 prefix.  (Note that the
      pseudo-interface must pick the IPv4 address corresponding to the
      prefix when encapsulating, or problems may ensue, e.g., on
      multi-interface routers.)

   o  Disallow traffic in which the destination IPv6 address is not a
      global address; in particular, link-local addresses, mapped
      addresses, and such should not be used.

   o  Discard traffic received from 6to4 routers with the destination as
      a 6to4 prefix.

4.  Threat Analysis

    This section discusses attacks against the 6to4 network or attacks
    caused by the 6to4 network.  The threats are discussed in light of
    the 6to4 deployment models defined in Section 2.

    There are three general types of threats:

   1.  Denial-of-Service (DoS) attacks, in which a malicious node
       prevents communication between the node under attack and other
       nodes.

   2.  Reflection Denial-of-Service (DoS) attacks, in which a malicious
       node reflects the traffic off unsuspecting nodes to a particular
       node (node under attack) in order to prevent communication
       between the node under attack and other nodes.

   3.  Service theft, in which a malicious node/site/operator may make
       unauthorized use of service.

   6to4 also provides a means for a "meta-threat", traffic laundering,
   in which some other attack is channeled through the third parties to
   make tracing the real origin of the attack more difficult.  This is
   used in conjunction with other threats, whether specific to 6to4 or
   not.

   At this point it is important to reiterate that the attacks are
   possible because

   1.  6to4 routers have to consider all 6to4 relays, and other 6to4
       routers, as "on-link",

   2.  6to4 relays have to consider all 6to4 routers as "on-link", and

   3.  it has been discovered that at least a couple of major 6to4
       implementations do not implement all the security checks.

   The attacks' descriptions are classified based on the target of the
   attack:

   1.  Attacks on 6to4 networks.

   2.  Attacks on IPv6 networks.

   3.  Attacks on IPv4 networks.

   Note that one of the mitigation methods listed for various attacks is
   based on the premise that 6to4 relays could have a feature limiting
   traffic to/from specific 6to4 sites.  At the time of this writing,
   this feature is speculative, and more work needs to be done to
   determine the logistics.

4.1.  Attacks on 6to4 Networks

   This section describes attacks against 6to4 networks.  Attacks that
   leverage 6to4 networks, but for which the ultimate victim is
   elsewhere (e.g., a native IPv6 user, an IPv4 user), are described
   later in the memo.

   6to4 relays and routers are IPv4 nodes, and there is no way for any
   6to4 router to confirm the identity of the IPv4 node from which it
   receives traffic -- whether from a legitimate 6to4 relay or some
   other node.  A 6to4 router has to process traffic from all IPv4
   nodes.  Malicious IPv4 nodes can exploit this property and attack
   nodes within the 6to4 network.

   It is possible to conduct a variety of attacks on the 6to4 nodes.
   These attacks are as follows:

   1.  Attacks with Neighbor Discovery (ND) Messages

   2.  Spoofing traffic to 6to4 nodes

   3.  Reflecting traffic from 6to4 nodes

   4.  Local IPv4 broadcast attack

4.1.1.  Attacks with ND Messages

   ATTACK DESCRIPTION

   Since the 6to4 router assumes that all the other 6to4 routers and
   6to4 relays are "on-link", it is possible to attack the 6to4 router
   by using ND messages from any node in the IPv4 network, unless a
   prior trust relationship has been established.

   The attacks target the 6to4 pseudo-interface.  As long as the 6to4
   addresses are not used in the source or destination address, the
   security checks specified by 6to4 take no stance on these packets.
   Typically they use link-local addresses.

   For example, an attack could be a Route Advertisement or Neighbor
   Advertisement message crafted specifically to cause havoc; the
   addresses in such a packet could resemble to the following:

   src_v6 = fe80::2           (forged address)
   dst_v6 = fe80::1           (valid or invalid address)
   src_v4 = 8.0.0.1           (valid or forged address)
   dst_v4 = 9.0.0.2           (valid address, matches dst_v6)

   These attacks are exacerbated if the implementation supports more
   tunneling mechanisms than 6to4 (or configured tunneling) because it
   is impossible to disambiguate such mechanisms, making it difficult to
   enable strict security checks (see Section 6.1).

   The Neighbor Discovery threats (Redirect DoS, or DoS) are described
   in [8].  Note that all attacks may not be applicable, as the 6to4

   pseudo-interface is assumed not to have a link-layer address (Section
   3.8 RFC 2893 [4]).  However, note that the 6to4 router can be either
   a router or host from the Neighbor Discovery perspective.

   THREAT ANALYSIS AND MITIGATION METHODS

   The attacks can be mitigated by using any of the following methods:

   o  The usage of ND messages could be prohibited.  This implies that
      all packets using addresses of scope link-local will be silently
      discarded.  Section 3.1 of RFC 3056 [1] leaves scope for future
      uses of link-local address.  This method has its pitfalls: It
      would prohibit any sort of ND message and thus close the doors on
      development and use of other ND options.  Whether this is a
      significant problem is another thing.

   o  The 6to4 pseudo-interface could be insulated from the other
      interfaces, particularly the other tunnel interfaces (if any), for
      example by using a separate neighbor cache.

   o  If ND messages are needed, either IPsec [4] or an extension of
      SEND could be used [9] to secure packet exchange using the
      link-local address; vanilla SEND would not work, as the link-layer
      does not have an address -- and IPsec would be rather complex.

   COMPARISON TO SITUATION WITHOUT 6to4

   Even though rather simply fixed, this attack is not new as such; the
   same is possible by using automatic tunneling [4] or configured
   tunneling (if one is able to spoof source IPv4 address to that of the
   tunnel end-point).

   However, as 6to4 provides open decapsulation, and automatic tunneling
   is being deprecated [10], 6to4 provides an easy means, which would
   not exist without it.

4.1.2.  Spoofing Traffic to 6to4 Nodes

   ATTACK DESCRIPTION

   The attacker - a malicious IPv4 or IPv6 node - can send packets that
   are difficult to trace (e.g., due to spoofing or going through a
   relay) to a 6to4 node.  This can be used e.g., to accomplish a DoS
   attack.

   The IPv6 and IPv4 addresses of the packets will be similar to the
   following:

   src_v6 = 2001:db8::1       (forged address)
   dst_v6 = 2002:0900:0002::1 (valid address)
   src_v4 = 8.0.0.1           (valid or forged address)
   dst_v4 = 9.0.0.2           (valid address, matches dst_v6)

   For attacks launched from a native IPv6 node, the src_v4 will be the
   address of the relay through which the traffic will reach the 6to4
   node.  From IPv4 nodes, src_v4 can be either a spoofed source address
   or the real one.

   The 6to4 router receives these packets from 8.0.0.1, decapsulates
   them, discards the IPv4 header containing the source address 8.0.0.1,
   and processes them as normal (the attacker has guessed or obtained
   "dst_v6" by using one of a number of techniques).

   This is a DoS attack on 6to4 nodes.

   This attack is similar to those shown in [11].

   EXTENSIONS

   Replies to the traffic will be directed to the src_v6 address,
   resulting in 6to4 nodes participating in a reflection DoS.  This
   attack is described in more detail in Section 4.2.3.  The replies
   (e.g., TCP SYN ACK, TCP RST, ICMPv6 Echo Reply, input sent to UDP
   echo service, ICMPv6 Destination Unreachable) are sent to the victim
   (src_v6), above.  All the traces from the original attacker (src_v4)
   have been discarded.  These return packets will go through a relay.

   Certain 6to4 networks may have a trivial ACL (Access Control List)
   based firewall that allows traffic to pass through if it comes from
   particular source(s).  Such a firewalling mechanism can be bypassed
   by address spoofing.  This attack can therefore be used for trivial
   ACL avoidance as well.  These attacks might be hampered because the
   replies from the 6to4 node to the spoofed address will be lost.

   THREAT ANALYSIS AND SOLUTIONS/MITIGATION METHODS

   The Denial-of-Service attack based on traffic spoofing is not new;
   the only twists come from the fact that traces of an attack are more
   easily lost, and that spoofing the IPv6 address is possible even to
   those who are unable to do so in their current networks.  The 6to4
   router typically does not log IPv4 addresses (as they would be
   treated as L2 addresses), and thus the source of the attack (if
   launched from an IPv4 node) is lost.  Because traces to the src_v4
   address are easily lost, these attacks can also be launched from IPv4
   nodes whose connections are ingress-filtered.

   However, often this is not a real factor, as usually the attackers
   are just zombies and real attackers may not even care whether the
   unspoofed source address is discovered.

   Malicious native IPv6 nodes could be caught easily if ingress
   filtering was enabled everywhere in the IPv6 Internet.

   These attacks are easy to perform, but the extent of harm is limited:

   o  For every packet sent, at most one reply packet is generated:
      there is no amplification factor.

   o  Attack packets, if initiated from an IPv6 node, will pass through
      choke point(s), namely a 6to4 relay; in addition to physical
      limitations, these could implement some form of 6to4-site-specific
      traffic limiting.

   On the other hand, a variety of factors can make the attacks serious:

   o  The attacker may have the ability to choose the relay, and he
      might employ the ones best suited for the attacks.  Also, many
      relays use 192.88.99.1 [3] as the source address, making tracing
      even more difficult (also see Section 4.2.6).

   o  The relay's IPv4 address may be used as a source address for these
      attacks, potentially causing a lot of complaints or other actions,
      as the relay might seem to be the source of the attack (see
      Section 4.2.6 for more).

   Some of the mitigation methods for such attacks are as follows:

   1.  Ingress filtering in the native IPv6 networks to prevent packets
       with spoofed IPv6 sources from being transmitted.  This would,
       thus, make it easy to identify the source of the attack.
       Unfortunately, it would depend on significant (or even complete)
       ingress filtering everywhere in other networks; while this is
       highly desirable, it may not be feasible.

   2.  Security checks in the 6to4 relay.  The 6to4 relay must drop
       traffic (from the IPv6 Internet) that has 6to4 addresses as
       source address; see Section 5 for more detail.  This has very
       little cost.

   However, these mitigation methods do not address the case of an IPv4
   node sending encapsulated IPv6 packets.

   No simple way to prevent such attacks exists, and longer-term
   solutions, such as ingress filtering [12] or itrace [13], would have

   to be deployed in both IPv6 and IPv4 networks to help identify the
   source of the attacks.  A total penetration is likely impossible.
   (Note that itrace work has been discontinued, as of this writing in
   July 2004.)

   COMPARISON TO SITUATION WITHOUT 6to4

   Traffic spoofing is not a new phenomenon in IPv4 or IPv6.  6to4 just
   makes it easier: Anyone can, regardless of ingress filtering, spoof a
   native IPv6 address to a 6to4 node, even if "maximal security" would
   be implemented and deployed.  Losing trails is also easier.

   Therefore, depending on how much one assumes ingress filtering is
   deployed for IPv4 and IPv6, this could be considered either a very
   serious issue or close to irrelevant compared to the IP spoofing
   capabilities without 6to4.

4.1.3.  Reflecting Traffic to 6to4 Nodes

   ATTACK DESCRIPTION

   Spoofed traffic (as described in Section 4.2.2) may be sent to native
   IPv6 nodes to perform a reflection attack against 6to4 nodes.

   The spoofed traffic is sent to a native IPv6 node, either from an
   IPv4 node (through a 6to4 relay) or from a native IPv6 node (unless
   ingress filtering has been deployed).  With the former, the sent
   packets would resemble the following:

       src_v6 = 2002:1234:1234::1 (forged address of the target 6to4 node) 
    dst_v6 = 2001:db8::1       (valid address)
    src_v4 = 8.0.0.1           (valid or invalid address)
EID 873 (Verified) is as follows:

Section: 4.1.3

Original Text:

    src_v6 = 2002:1234:1234::1 (forged address of the target 6to4 node)
    dst_v6 = 2002:0900:0002::1 (valid address)
    src_v4 = 8.0.0.1           (valid or invalid address)
    dst_v4 = 9.0.0.2           (valid address, matches dst_v6)

Corrected Text:

    src_v6 = 2002:1234:1234::1 (forged address of the target 6to4 node)
    dst_v6 = 2001:db8::1       (valid address)
    src_v4 = 8.0.0.1           (valid or invalid address)
Notes:
copy/paste error. Traffic is sent to the native IPv6 node, so the
destination address should be non-2002::/16. When 6to4 is not used,
dst_v4 is not applicable so it could be removed.

from pending
Note that an attack through the relay is prevented if the relay implements proper decapsulation security checks (see Section 5 for details) unless the IPv4 node can spoof the source address to match src_v6. Similarly, the attack from native IPv6 nodes could be prevented by global ingress filtering deployment. These attacks can be initiated by native IPv6, IPv4, or 6to4 nodes. EXTENSIONS A distributed Reflection DoS can be performed if a large number of nodes are involved in sending spoofed traffic with the same src_v6. Malicious 6to4 nodes can also (try to) initiate this attack by bouncing traffic off 6to4 nodes in other 6to4 sites. However, this attack may not be possible, as the 6to4 router (in the site from which the attack is launched) will filter packets with forged source addresses (with security checks mentioned in Section 5). THREAT ANALYSIS AND SOLUTIONS/MITIGATION METHODS In this case, the reverse traffic comprises replies to the messages received by the 6to4 nodes. The attacker has less control on the packet type, and this would inhibit certain types of attacks. For example, flooding a 6to4 node with TCP SYN packets will not be possible (but e.g., a SYN-ACK or RST would be). These attacks may be mitigated in various ways: o Implementation of ingress filtering by the IPv4 service providers. This would prevent forging of the src_v4 address and help in closing down on the culprit IPv4 nodes. Note that it will be difficult to shut down the attack if a large number of IPv4 nodes are involved. These attacks may be also be stopped at the 6to4 sites if the culprit src_v4 address is identified, and if it is constant, by filtering traffic from this address. Note that it would be difficult to implement this method if appropriate logging were not done by the 6to4 router or if a large number of 6to4 nodes, and/or a large number of IPv4 nodes were participating in the attack. Unfortunately, because many IPv4 service providers don't implement ingress filtering, for whatever reasons, this may not be a satisfactory solution. o Implementation of ingress filtering by all IPv6 service providers would eliminate this attack, because src_v6 could not be spoofed as a 6to4 address. However, expecting this to happen may not be practical. o Proper implementation of security checks (see Section 5) both at the 6to4 relays and routers would eliminate an attack launched from an IPv4 node, except when the IPv4 source address was also spoofed -- but then the attacker would have been able to attack the ultimate destination directly. o Rate limiting traffic at the 6to4 relays. In a scenario where most of the traffic is passing through few 6to4 relays, these relays can implement traffic rate-limiting features and rate-limit the traffic from 6to4 sites. COMPARISON TO SITUATION WITHOUT 6to4 This particular attack can be mitigated by proper implementation of security checks (which is quite straightforward) and ingress filtering; when ingress filtering is not implemented, it is typically easier to attack directly than through reflection -- unless "traffic laundering" is an explicit goal of the attack. Therefore, this attack does not seem very serious. 4.1.4. Local IPv4 Broadcast Attack ATTACK DESCRIPTION This threat is applicable if the 6to4 router does not check whether the IPv4 address to which it tries to send encapsulated IPv6 packets is a local broadcast address or a multicast address. This threat is described in the specification [1], and implementing the checks eliminates this threat. However, as checks have not been widely implemented, the threat is included here for completeness. There practically two kinds of attacks: when a local 6to4 user tries to send packets to the address corresponding to the broadcast address, and when someone is able to do so remotely. In the first option, assume that 9.0.0.255 is the 6to4 router's broadcast address. After receiving the packet with a destination address like "2002:0900:00ff::bbbb" from a local 6to4 node, if the router doesn't check the destination address for subnet broadcast, it would send the encapsulated protocol-41 packet to 9.0.0.255. This would be received by all nodes in the subnet, and the responses would be directed to the 6to4 router. Malicious sites may also embed forged 6to4 addresses in the DNS, use of which by a 6to4 node would result in a local broadcast by the 6to4 router. One way to perform this attack would be to send an HTML mail containing a link to an invalid URL (for example, http://[2002:0900:00ff::bbbb]/index.html) to all users in a 6to4 technology based network. Opening of the mail simultaneously would result in a broadcast storm. The second kind of attack is more complex: The attack can be initiated by IPv4 nodes not belonging to the local network as long as they can send traffic with invalid (for example 2002:0900:00ff::bbbb) source address. The 6to4 router has to respond to the traffic by sending ICMPv6 packets back to the source, (e.g., Hop Limit Exceeded or Destination Unreachable). The packet would be as follows: src_v6 = 2002:0800:00ff::bbbb (broadcast address of the router) dst_v6 = 2002:0800:0001::0001 (valid non-existent address) This is a DoS attack. EXTENSIONS The attacks could also be directed at non-local broadcast addresses, but these would be so-called "IPv4 directed broadcasts", which have (luckily enough) already been extensively blocked in the Internet. THREAT ANALYSIS AND SOLUTIONS/MITIGATION METHODS The attack is based on the premise that the 6to4 router has to send a packet that embeds an invalid IPv4 address to an IPv6 address. Such an attack is easily thwarted by ensuring that the 6to4 router does not transmit packets to invalid IPv4 addresses. Specifically, traffic should not be sent to broadcast or multicast IPv4 addresses. COMPARISON TO SITUATION WITHOUT 6to4 The first threat is similar to what is already possible with IPv4, but IPv6 does not have broadcast addresses. The second, a more complex threat, is, similarly, also available in IPv4. In consequence, the security does not seem to be significantly worse than with IPv4, and even that is restricted to the site(s) with 6to4 implementations that haven't been secured as described in Section 5. 4.2. Attacks on Native IPv6 Internet This section describes attacks against native IPv6 Internet that somehow leverage 6to4 architecture. Attacks against 6to4 nodes were described in the previous section. 6to4 and IPv4 nodes can access native IPv6 nodes through the 6to4 relay routers. Thus, the 6to4 relays play a crucial role in any attack on native IPv6 nodes by IPv4 nodes or 6to4 nodes. 6to4 relays have only one significant security check they must perform for general safety: When decapsulating IPv4 packets, they check that 2002:V4ADDR::/48 and V4ADDR match in the source address. If this is not done, several threats become more serious; in the following analysis, it is assumed that such checks are implemented. 6to4 relay should not relay packets between 6to4 addresses. In particular, packets decapsulated from 6to4 routers should not be encapsulated toward 6to4 routers, as described in Section 5. Similarly, packets with 6to4 source and destination addresses sent from IPv6 nodes should not be relayed. It is not clear whether this kind of check is typically implemented. The attacks described below assume that such checks are not implemented. 4.2.1. Attacks with ND Messages These attacks are the same as those employed against 6to4 routers, as described in Section 4.1.1. 4.2.2. Spoofing Traffic to Native IPv6 Node ATTACK DESCRIPTION The attacker - a malicious IPv4 or 6to4 node - can send packets with a spoofed (or not spoofed) 6to4 source address to a native IPv6 node to accomplish a DoS attack. The threat is similar to that involving 6to4 routers, as described in Section 4.1.2. The difference here is that the attack is initiated by IPv4 or 6to4 nodes. The source IPv6 address may or may not be spoofed. Note that, as mentioned above, the relay is assumed to correlate the source IPv4 address with the address embedded in the source IPv6 address during decapsulation. A side effect is that all spoofed traffic will have a 6to4 source address. EXTENSIONS Spoofed traffic may also be sent to native IPv6 nodes either by other native IPv6 nodes, by 6to4 nodes, or by malicious IPv4 nodes to conduct Reflection DoS on either native IPv6 nodes or 6to4 nodes. Certain native IPv6 networks may have a trivial ACL (Access Control List) based firewall that allows traffic to pass through if it comes from particular source(s). Such a firewalling mechanism can be bypassed by address spoofing. This attack can therefore be used for trivial ACL avoidance as well. These attacks might be hampered by lost replies from the 6to4 node to the spoofed address. THREAT ANALYSIS AND SOLUTIONS/MITIGATION METHODS The Denial-of-Service attack based on traffic spoofing is not new; the only twist is that traces of an attack are more easily lost. The 6to4 relay typically does not log IPv4 addresses (as they would be treated as L2 addresses), and thus the source of the attack (if launched from an IPv4 node) is lost. Because traces to the src_v4 address are easily lost, these attacks can also be launched from IPv4 nodes whose connections are ingress-filtered. These attacks might not be easy to perform and might be hampered because of the following: o It might be difficult to launch such attacks from 6to4 nodes because even if the 6to4 routers allow spoofing of the source IPv6 address, the 6to4 relay would check whether the source V4ADDR is the same as the one embedded in the source IPv6 address. Thus, 6to4 nodes will be forced to use the correct IPv6 prefix while launching an attack, making it easy to close such attacks. o Packets may pass through choke point(s), namely a 6to4 relay. In addition to physical limitations, there could be some sort of traffic rate limiting mechanisms that may be implemented, and these could tone down the attack. o For every packet sent, at most one reply packet is generated: There is no amplification factor. Some of the mitigation methods for such attacks are as follows: 1. Ingress filtering in the IPv4 Internet to prevent packets with a spoofed IPv4 source from being transmitted. As the relay checks that the 6to4 address embeds the IPv4 address, no spoofing can be achieved unless IPv4 addresses can be spoofed. However, this would probably be an unfeasible requirement. 2. Security checks in the 6to4 relay. The 6to4 relay must drop traffic (from 6to4 nodes, or IPv4 nodes) with non-6to4 addresses as the source address, or for which the source IPv4 address does not match the address embedded in the source IPv6 address. COMPARISON TO SITUATION WITHOUT 6to4 Compared to Section 4.1.2, which describes more serious threats, this threat appears to be slightly more manageable. If the relays perform proper decapsulation checks, the spoofing can only be achieved, to a 6to4 source address, when the IPv4 address is spoofable as well. 4.2.3. Reflecting Traffic to Native IPv6 Nodes ATTACK DESCRIPTION These reflection attacks are similar to that involving 6to4 routers, as described in Section 4.1.3. Traffic may be reflected off native IPv6 nodes, or off 6to4 nodes. The attack can be initiated by one of the following: o Native IPv6 nodes. These nodes can send invalid traffic with spoofed native IPv6 addresses to valid 6to4 nodes. Replies from the 6to4 nodes are part of a reflection attack. o IPv4 nodes. These nodes can send traffic with native IPv6 source addresses (encapsulated by the IPv4 node itself into a protocol-41 packet) to 6to4 nodes. Replies from the 6to4 nodes are part of a reflection attack. o 6to4 nodes. These nodes can perform attacks similar to those by IPv4 nodes, but this would require spoofing of the source address at the 6to4 site before encapsulation, which is likely to be difficult. When launched from a native IPv6 node, the traffic goes through 6to4 relays twice, both before and after the reflection; when launched from a 6to4/IPv4 node, the traffic goes through a relay only after the reflection. EXTENSIONS A distributed reflection DoS can be performed if a large number of native IPv6 nodes or IPv4/6to4 nodes are involved in sending spoofed traffic with the same source IPv6 address. THREAT ANALYSIS AND SOLUTIONS/MITIGATION METHODS Some of the mitigation methods for such attacks are as follows: 1. Attacks from the native IPv6 nodes could be stopped by implementing ingress filtering in the IPv6 Internet; hopefully this will become commonplace, but past experience of IPv4 ingress filtering deployment (or lack thereof) does not promise much. 2. Two measures are needed to stop or mitigate the attacks from IPv4 nodes: 1) Implementing ingress filtering in the IPv4 internet, and 2) logging IPv4 source addresses in the 6to4 router. 3. Attacks from 6to4 nodes in other sites can be stopped if the 6to4 routers in those sites implement egress filtering. This could be done by those sites, but the sites that are most likely to be abused are typically also those most likely to neglect installing appropriate filtering at their edges. 4. The traffic passes through one or two relays, and traffic rate limiting in the 6to4 relays might help tone down the reflection attack. COMPARISON TO SITUATION WITHOUT 6to4 Even though there are means to mitigate it, the attack is still rather efficient, especially when used by native IPv6 nodes with spoofed addresses. Using 6to4 relays and routers could easily take down the 6to4 relay system and/or provide an easy means for traffic laundering. However, if the attack is intended to DoS the victim, this can be achieved more smoothly by doing it directly (as the source address spoofing was available as well). Therefore, the threat to the availability and stability of the 6to4 relay system itself seems to be higher than to the native IPv6 Internet. 4.2.4. Local IPv4 Broadcast Attack This attack is similar to the ones employed against 6to4 routers, as described in Section 4.1.4. There are slight differences with regard to the source of the attacks. This attack can be initiated by: o native IPv6 nodes that may send traffic to the relay's subnet broadcast address, and o IPv4 nodes that may send traffic with a spoofed source IP address (to be the relay's broadcast address) to elicit replies (e.g., ICMPv6 Hop Limit Exceeded) from the 6to4 relay to its local nodes. The first approach is more dangerous than those in Section 4.1.4 because it can be initiated by any IPv6 node (allowed to use the relay); the approach is not limited to local users. The second approach is trickier and not really useful. For it to succeed, the relay would have to accept native source addresses over the 6to4 pseudo-interface (we did not assume this check was implemented), as if coming from another relay, triggering an ICMPv6 message to the relay's local IPv4 subnet. The former method is more lucrative. EXTENSIONS None. THREAT ANALYSIS AND SOLUTIONS/MITIGATION METHODS The threat is restricted to the relay's local subnet and is fixed by tightening the 6to4 security checks. COMPARISON TO SITUATION WITHOUT 6to4 This scenario is caused by 6to4, but fortunately the issue is not serious. 4.2.5. Theft of Service ATTACK DESCRIPTION The 6to4 relay administrators would often want to use some policy to limit the use of the relay to specific 6to4 sites and/or specific IPv6 sites. The policy control is usually enacted by applying restrictions to where the routing information for 2002::/16 and/or 192.88.99.0/24 (if the anycast address used [3]) will spread.
EID 874 (Verified) is as follows:

Section: 4.2.5

Original Text:

    The policy control is usually enacted by applying restrictions to
    where the routing information for 2002::/16 and/or 192.188.99.0/24
    (if the anycast address used [3]) will spread.

Corrected Text:

    The policy control is usually enacted by applying restrictions to
    where the routing information for 2002::/16 and/or 192.88.99.0/24
    (if the anycast address used [3]) will spread.
Notes:
typo in the anycast address.


from pending
Some users may be able to use the service regardless of these controls, by o configuring the address of the relay using its IPv4 address instead of 192.88.99.1, or o using the routing header to route IPv6 packets to reach specific 6to4 relays. (Other routing tricks, such as using static routes, may also be used.) EXTENSIONS None. THREAT ANALYSIS AND SOLUTIONS/MITIGATION METHODS Attempts to use the relay's IPv4 address instead of 192.88.99.1 can be mitigated in the following ways: 1. IPv4 domains should prevent use of the actual IPv4 address of the relay instead of 192.88.99.1. 2. Usage of access lists in the 6to4 relay to limit access. This is only feasible if the number of IP networks the relay is supposed to serve is relatively low. 3. The 6to4 relay should filter out arriving tunneled packets with protocol 41 (IPv6) that do not have 192.88.99.1 as the destination address. The other threat, of using routing tricks in the IPv6 networks to reach the 6to4 relay, has similar solutions: 1. Usage of access lists in the relay to limit access. 2. Filtering out the packets with a routing header (although this may have other implications). 3. Monitoring the source addresses going through the relay to detect, e.g., peers setting up static routes. Routing Header is not specific to 6to4. The main thing one could do with it here would be to select the relay. Some generic threats about routing header use are described in [11]. As this threat does not have implications for anything other than the organization providing 6to4 relay, it is not analyzed any further. COMPARISON TO SITUATION WITHOUT 6to4 These threats are specific to 6to4 relays (or in general anycast services) and do not exist in networks without 6to4. 4.2.6. Relay Operators Seen as Source of Abuse ATTACK DESCRIPTION Several attacks use 6to4 relays to anonymize the traffic; this often results in packets being tunneled from the relay to a supposedly-6to4 site. However, as was pointed out in Section 4.2, the IPv4 source address used by the relay could, on a cursory look, be seen as the source of these "protocol-41" attacks. This could cause a number of concerns for the operators deploying 6to4 relay service, including the following: o being contacted a lot (via email, phone, fax, or lawyers) on suspected "abuse", o having the whole IPv4 address range rejected as a source of abuse or spam, causing outage to other operations as well, or o causing the whole IPv4 address range to be blacklisted in some "spammer databases", if the relay were used for those purposes. This threat seems slightly similar to the outburst of SMTP abuse caused by open relays but is more generic. EXTENSIONS None. THREAT ANALYSIS AND SOLUTIONS/MITIGATION METHODS This problem can be avoided (or, really, "made someone else's problem") by using the 6to4 anycast address in 192.88.99.0/24 as the source address. Blacklisting or rejecting this should not cause problems to the other operations. Further, when someone files complaints to the owner of 192.88.99.0/24, depending on which registry they are querying, they might get, for example: o knowledge that this is a special IANA address block, with no real contact person, o knowledge that this is a special address block for RFC 3068, or o knowledge that this is a special address block for RFC 3068, and that there are multiple entries by relay operators in the database. Any of these, at least when processed by a human, should show that the 6to4 relay is in fact innocent. Of course, this could result in reports going to the closest anycast 6to4 relay as well, which had nothing to do with the incident. However, the widespread usage of 192.88.99.1 as the source address may make it more difficult to disambiguate the relays, which might be a useful feature for debugging purposes. COMPARISON TO SITUATION WITHOUT 6to4 This threat is caused by 6to4 deployment but can be avoided, at least in the short-term, by using 192.88.99.1 as the source address. 4.3. Attacks on IPv4 Internet There are two types of attacks on the IPv4 internet - spoofed traffic, and reflection. These can be initiated by native IPv6 nodes, 6to4 nodes, and IPv4 nodes. Attacks initiated by IPv4 nodes that send spoofed traffic, which would not use the 6to4 infrastructure, are considered out of the scope of this document. 6to4 infrastructure may be used in reflection attacks initiated by IPv4 nodes. It is difficult for these attacks to be effective, as the traffic sent out will be IPv6-in-IPv4. Such traffic will be rejected by most IPv4 nodes unless they have implemented some sort of IPv6-in-IPv4 tunneling. 4.4. Summary of the Attacks Columns: o Section number. The section that describes the attack. o Attack name. o Initiator. The node that initiates the attack. * I_4 - IPv4 node * I_6 - native IPv6 node * 6to4 - 6to4 node * * - All of the above o Victim. The victim node * I_4 - IPv4 node * I_6 - native IPv6 node * 6to4 - 6to4 node * Relay - 6to4 relay * Router - 6to4 router o ToA. Type of Attack * D - DoS * R - Reflection DoS * T - Theft of Service o Fix. Specified who is responsible for fixing the attack. * 6 - The 6to4 developer and/or operator can completely mitigate this attack. * 6* - The 6to4 developer and/or operator can partially mitigate this attack. * E - This threat cannot be fixed by the 6to4 developer or the 6to4 operator. Summary of attacks on a 6to4 network: +-------+----------------------+---------+----------+-----+-----+ | Sec | Attack name |Initiator| Victim | ToA | Fix | +-------+----------------------+---------+----------+-----+-----+ | 4.1.1 | Attacks with ND | I_4 | Router | D | 6 | +-------+----------------------+---------+----------+-----+-----+ | 4.1.2 | Spoofing Traffic | I_4,I_6 | 6to4 | D | E | +-------+----------------------+---------+----------+-----+-----+ | 4.1.3 | Reflection Attacks | * | 6to4 | R | 6* | +-------+----------------------+---------+----------+-----+-----+ | 4.1.4 | Local IPv4 Broadcast | * | Router | D | 6 | +-------+----------------------+---------+----------+-----+-----+ Figure 9 Summary of attacks on the native IPv6 internet: +-------+----------------------+---------+----------+-----+-----+ | Sec | Attack name |Initiator| Victim | ToA | Fix | +-------+----------------------+---------+----------+-----+-----+ | 4.2.1 | Attacks with ND | I_4 | Relay | D | 6 | +-------+----------------------+---------+----------+-----+-----+ | 4.2.2 | Spoofing Traffic | I_4,6to4| I_6 | D | 6* | +-------+----------------------+---------+----------+-----+-----+ | 4.2.3 | Reflection Attacks | * | I_6 | R | 6* | +-------+----------------------+---------+----------+-----+-----+ | 4.2.4 | Local IPv4 Broadcast | * | Relay | D | 6 | +-------+----------------------+---------+----------+-----+-----+ | 4.2.5 | Theft of Service | 6to4 | Relay | T | 6 | +-------+----------------------+---------+----------+-----+-----+ | 4.2.6 | Relay Operators ... | - | - | D | 1) | +-------+----------------------+---------+----------+-----+-----+ Figure 10 Notes: 1) This attack is a side-effect of the other attacks and thus does not have any Initiator, Victim, and Fix. It is a Denial of Service attack not on the network but on the organization in-charge of the relay. Summary of attacks on IPv4 internet: +-------+----------------------+---------+----------+-----+-----+ | Sec | Attack name |Initiator| Victim | ToA | Fix | +-------+----------------------+---------+----------+-----+-----+ | 4.3 | Spoofing Traffic | * | I_4 | D | 6* | +-------+----------------------+---------+----------+-----+-----+ | 4.3 | Reflection Attacks | * | I_4 | R | 6* | +-------+----------------------+---------+----------+-----+-----+ Figure 11 5. Implementing Proper Security Checks in 6to4 This section describes several ways to implement the security checks required or implied by the specification [1] or augmented by this memo. These do not, in general, protect against most of the threats listed above in the "Threat Analysis" section. They are only prerequisites for a relatively safe and simple 6to4 implementation. Note that, in general, the 6to4 router or relay does not know whether it is acting as a router or relay. It would be possible to include a toggle to specify the behaviour, to be used when, e.g., the interface is brought up, but as of February 2004, no implementations were known to do that. Therefore, the checks are described as that which works independently of whether the node is a router or relay. 5.1. Encapsulating IPv6 into IPv4 The checks described in this section are to be performed when encapsulating IPv6 into IPv4. The encapsulation rules are mainly designed to keep implementors from "shooting themselves in the foot." For example, the source address check would verify that the packet will be acceptable to the decapsulator, or the sanity checks would ensure that addresses derived from private addresses are not used (which would be equally unacceptable). src_v6 and dst_v6 MUST pass ipv6-sanity checks (see below) else drop if prefix (src_v6) == 2002::/16 ipv4 address embedded in src_v6 MUST match src_v4 else if prefix (dst_v6) == 2002::/16 dst_v4 SHOULD NOT be assigned to the router else drop /* we somehow got a native-native ipv6 packet */ fi accept 5.2. Decapsulating IPv4 into IPv6 The checks described in this section are to be performed when decapsulating IPv4 into IPv6. They will be performed in both the 6to4 router and relay. src_v4 and dst_v4 MUST pass ipv4-sanity checks, else drop src_v6 and dst_v6 MUST pass ipv6-sanity checks, else drop if prefix (dst_v6) == 2002::/16 ipv4 address embedded in dst_v6 MUST match dst_v4 if prefix (src_v6) == 2002::/16 ipv4 address embedded in src_v6 MUST match src_v4 dst_v4 SHOULD be assigned to the router fi elif prefix (src_v6) == 2002::/16 ipv4 address embedded in src_v6 MUST match src_v4 dst_v4 SHOULD be assigned to the router (see notes below) else drop /* the we somehow got a native-native ipv6 packet */ fi accept 5.3. IPv4 and IPv6 Sanity Checks The encapsulation and decapsulation checks include certain sanity checks for both IPv4 and IPv6. These are described here in detail. 5.3.1. IPv4 IPv4 address MUST be a global unicast address, as required by the 6to4 specification. The disallowed addresses include those defined in [14], and others widely used and known not to be global. These are o 0.0.0.0/8 (the system has no address assigned yet) o 10.0.0.0/8 (private) o 127.0.0.0/8 (loopback) o 172.16.0.0/12 (private) o 192.168.0.0/16 (private) o 169.254.0.0/16 (IANA Assigned DHCP link-local) o 224.0.0.0/4 (multicast) o 240.0.0.0/4 (reserved and broadcast) In addition, the address MUST NOT be any of the system's broadcast addresses. This is especially important if the implementation is made so that it can o receive and process encapsulated IPv4 packets arriving at its broadcast addresses, or o send encapsulated IPv4 packets to one of its broadcast addresses. 5.3.2. IPv6 IPv6 address MUST NOT be o 0::/16 (compatible, mapped addresses, loopback, unspecified, ...) o fe80::/10 (link-local) o fec0::/10 (site-local) o ff00::/8 (any multicast) Note: Only link-local multicast would be strictly required, but it is believed that multicast with 6to4 will not be feasible, so it has been disallowed as well. In addition, it MUST be checked that equivalent 2002:V4ADDR::/48 checks, where V4ADDR is any of the above IPv4 addresses, will not be passed. 5.3.3. Optional Ingress Filtering In addition, the implementation in the 6to4 router may perform some form of ingress filtering (e.g., Unicast Reverse Path Forwarding checks). For example, if the 6to4 router has multiple interfaces, of which some are "internal", receiving either IPv4 or IPv6 packets with source address belonging to any of these internal networks from the Internet might be disallowed. If these checks are implemented and enabled by default, it's recommended that there be a toggle to disable them if needed. 5.3.4. Notes about the Checks The rule "dst_v4 SHOULD be assigned to the router" is not needed if the 6to4 router implementation only accepts and processes encapsulated IPv4 packets arriving to its unicast IPv4 addresses, and when the destination address is known to be a local broadcast address, it does not try to encapsulate and send packets to it. (See Sections 4.1.4 and 4.2.4 about this threat.) Some checks, especially the IPv4/IPv6 Sanity Checks, could be at least partially implementable with system-level access lists, if one would like to avoid placing too many restrictions in the 6to4 implementation itself. This depends on how many hooks are in place for the access lists. In practice, it seems that this could not be done effectively enough unless the access list mechanism is able to parse the encapsulated packets. 6. Issues in 6to4 Implementation and Use This section tries to give an overview of some of the problems 6to4 implementations face, and the kind of generic problems the 6to4 users could come up with. 6.1. Implementation Considerations with Automatic Tunnels There is a problem with multiple transition mechanisms if strict security checks are implemented. This may vary a bit from implementation to implementation. Consider three mechanisms using automatic tunneling: 6to4, ISATAP [15], and Automatic Tunneling using Compatible Addresses [4] (currently removed [10] but typically still supported). All of these use IP-IP (protocol 41) [16] IPv4 encapsulation with, more or less, a pseudo-interface. When a router, which has any two of these enabled, receives an IPv4 encapsulated IPv6 packet src_v6 = 2001:db8::1 dst_v6 = 2002:1010:1010::2 src_v4 = 10.0.0.1 dst_v4 = 20.20.20.20 What can it do? How should it decide which transition mechanism this belongs to; there is no "transition mechanism number" in the IPv6 or IPv4 header to signify this. (This can also be viewed as a flexibility benefit.) Without any kind of security checks (in any of the implemented methods), these often just "work", as the mechanisms aren't differentiated but handled in "one big lump". Configured tunneling [4] does not suffer from this, as it is point-to-point and based on src_v6/dst_v6 pairs of both IPv4 and IPv6 addresses, so the tunnel interface can be logically deduced. Solutions for this include 1) not using more than one automatic tunneling mechanism in a node and 2) binding different mechanisms to different IPv4 addresses. 6.2. A Different Model for 6to4 Deployment Even though this was already discussed in Section 4.1.2, it bears some additional elaboration, as it was the only problem that cannot be even partially solved using the current deployment model. There are some mitigation methods. 6to4 routers receive traffic from non-6to4 ("native") sources via 6to4 relays. 6to4 routers have no way of matching the IPv4 source address of the relay with the non-6to4 IPv6 address of the source. Consequently, anyone can spoof any non-6to4 IPv6 address by sending traffic, encapsulated, directly to 6to4 routers. It could be possible to turn the deployment assumptions of 6to4 around a bit to eliminate some threats caused by untrusted 6to4 relays: o Every dual-stack site (or even ISP) would be required to have its own 6to4 relay. (This assumes that IPv6-only is so far away that 6to4 would be retired by that point.) That is, there would not be third-party relays, and 2002::/16 and 192.88.99.0/24 routes would not need to be advertised globally. o The security implications of 6to4 use could be pushed back to the level of trust inside the site or ISP (or their acceptable use policies). This is something that the sites and ISPs should already be familiar with already. However, this presents a number of problems: This model would shift most of the burden of supporting 6to4 to IPv6 sites that don't employ or use 6to4 at all, i.e., "those who deploy proper native dual-stack." It could be argued that the deployment pain should be borne by 6to4 users, not by the others. The main advantage of 6to4 is easy deployment and free relays. This would require that everyone the 6to4 sites wish to communicate with implement these measures. The model would not fix the "relay spoofing problem", unless everybody also deployed 6to4 addresses on the nodes (alongside with native addresses, if necessary), which would in turn change 6to4 to operate without relays completely. 7. Security Considerations This document discusses security considerations of 6to4. Even if proper checks are implemented, there are a large number of different security threats; these threats are analyzed in Section 4. There are mainly four classes of potential problem sources: 1. 6to4 routers not being able to identify whether relays are legitimate 2. Wrong or impartially implemented 6to4 router or relay security checks 3. 6to4 architecture used to participate in DoS or reflected DoS attacks or made to participate in "packet laundering", i.e., making another attack harder to trace 4. 6to4 relays being subject to "administrative abuse" e.g., theft of service or being seen as a source of abuse. The first is the toughest problem, still under research. The second can be fixed by ensuring the correctness of implementations; this is important. The third is also a very difficult problem, impossible to solve completely; therefore it is important to be able to analyze whether this results in a significant increase of threats. The fourth problem seems to have feasible solutions. These are analyzed in detail in "Threat Analysis", in Section 4. 8. Acknowledgments Some issues were first brought up by Itojun Hagino in [17], and Alain Durand introduced one specific problem at IETF51 in August 2001 (though there was some discussion on the list prior to that); these two gave the authors the push to start looking into the details of securing 6to4. Alexey Kuznetsov brought up the implementation problem with IPv6 martian checks. Christian Huitema formulated the rules that rely on 6to4 relays using only anycast. Keith Moore brought up the point about reduced flexibility. Brian Carpenter, Tony Hain, and Vladislav Yasevich are acknowledged for lengthy discussions. Alain Durand reminded the authors about relay spoofing problems. Brian Carpenter reminded the authors about the BGP-based 6to4 router model. Christian Huitema gave a push for a more complete threat analysis. Itojun Hagino spelled out the operators' fears about 6to4 relay abuse. Rob Austein brought up the idea of a different 6to4 deployment model. In the latter phase, discussions with Christian Huitema, Brian Carpenter, and Alain Durand were helpful when improving the document. David Malone, Iljitsch van Beijnum, and Tim Chown gave feedback on the document. 9. References 9.1. Normative References [1] Carpenter, B. and K. Moore, "Connection of IPv6 Domains via IPv4 Clouds", RFC 3056, February 2001. [2] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [3] Huitema, C., "An Anycast Prefix for 6to4 Relay Routers", RFC 3068, June 2001. 9.2. Informative References [4] Gilligan, R. and E. Nordmark, "Transition Mechanisms for IPv6 Hosts and Routers", RFC 2893, August 2000. [5] IANA, "Special-Use IPv4 Addresses", RFC 3330, September 2002. [6] Rekhter, Y. and T. Li, "A Border Gateway Protocol 4 (BGP-4)", RFC 1771, March 1995. [7] Draves, R., "Default Address Selection for Internet Protocol version 6 (IPv6)", RFC 3484, February 2003. [8] Nikander, P., Kempf, J., and E. Nordmark, "IPv6 Neighbor Discovery (ND) Trust Models and Threats", RFC 3756, May 2004. [9] Arkko, J., Kempf, J., Sommerfeld, B., Zill, B., and P. Nikander, "SEcure Neighbor Discovery (SEND)", Work in Progress, July 2004. [10] Nordmark, E. and R. Gilligan, "Basic Transition Mechanisms for IPv6 Hosts and Routers", Work in Progress, September 2004. [11] Savola, P., "Security of IPv6 Routing Header and Home Address Options", Work in Progress, March 2002. [12] Ferguson, P. and D. Senie, "Network Ingress Filtering: Defeating Denial of Service Attacks which employ IP Source Address Spoofing", BCP 38, RFC 2827, May 2000. [13] Bellovin, S., Leech, M. and T. Taylor, "ICMP Traceback Messages", Work in Progress, February 2003. [14] Baker, F., "Requirements for IP Version 4 Routers", RFC 1812, June 1995. [15] Templin, F., Gleeson, T., Talwar, M. and D. Thaler, "Intra-Site Automatic Tunnel Addressing Protocol (ISATAP)", Work in Progress, May 2004. [16] Simpson, W., "IP in IP Tunneling", RFC 1853, October 1995. [17] Hagino, J., "Possible abuse against IPv6 transition technologies", Work in Progress, July 2000. Appendix A. Some Trivial Attack Scenarios Outlined Here, a few trivial attack scenarios are outlined -- ones that are prevented by implementing checks listed in [1] or in section 6. When two 6to4 routers send traffic to each others' domains, the packet sent by RA to RB resembles the following: src_v6 = 2002:0800:0001::aaaa dst_v6 = 2002:0800:0002::bbbb src_v4 = 8.0.0.1 (added when encapsulated to IPv4) dst_v4 = 8.0.0.2 (added when encapsulated to IPv4) When the packet is received by IPv4 stack on RB, it will be decapsulated so that only src_v6 and dst_v6 remain, as originally sent by RA: src_v6 = 2002:0800:0001::aaaa dst_v6 = 2002:0800:0002::bbbb As every other node is just one hop away (IPv6-wise) and the link-layer (IPv4) addresses are lost, this may open many possibilities for misuse. As an example, unidirectional IPv6 spoofing is made trivial because nobody can check (without delving into IP-IP packets) whether the encapsulated IPv6 addresses were authentic. (With native IPv6, this can be done by, e.g., RPF-like mechanisms or access lists in upstream routers.) src_v6 = 2002:1234:5678::aaaa (forged) dst_v6 = 2002:0800:0002::bbbb src_v4 = 8.0.0.1 (added when encapsulated to IPv4) dst_v4 = 8.0.0.2 (added when encapsulated to IPv4) A similar attack with "src" being the native address is made possible, even with the security checks, by having the sender node pretend to be a 6to4 relay router. More worries come into the picture if, e.g., src_v6 = ::ffff:[some trusted IPv4 in a private network] src_v6/dst_v6 = ::ffff:127.0.0.1 src_v6/dst_v6 = ::1 src_v6/dst_v6 = ... Some implementations might have been careful enough to design the stack so as to avoid the incoming (or reply) packets going to IPv4 packet processing through special addresses (e.g., IPv4-mapped addresses), but who can say for all ... Authors' Addresses Pekka Savola CSC/FUNET Espoo Finland EMail: psavola@funet.fi Chirayu Patel All Play, No Work 185, Defence Colony Bangalore, Karnataka 560038 India Phone: +91-98452-88078 EMail: chirayu@chirayu.org URI: http://www.chirayu.org Full Copyright Statement Copyright (C) The Internet Society (2004). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the IETF's procedures with respect to rights in IETF Documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf- ipr@ietf.org. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society.