This is a purely informative rendering of an RFC that includes verified errata. This rendering may not be used as a reference.

The following 'Verified' errata have been incorporated in this document: EID 1791
Network Working Group                                             B. Ray
Request for Comments: 3728                        PESA Switching Systems
Category: Standards Track                                        R. Abbi
                                                                 Alcatel
                                                           February 2004


              Definitions of Managed Objects for Very High
                 Speed Digital Subscriber Lines (VDSL)

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2004).  All Rights Reserved.

Abstract

   This document defines a Management Information Base (MIB) module for
   use with network management protocols in the Internet community.  In
   particular, it describes objects used for managing Very High Speed
   Digital Subscriber Line (VDSL) interfaces.

Table of Contents

   1.  The Internet-Standard Management Framework . . . . . . . . . .  2
   2.  Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
       2.1.  Relationship of the VDSL Line MIB Module to other MIB
             Modules. . . . . . . . . . . . . . . . . . . . . . . . .  2
       2.2.  Conventions used in the MIB Module . . . . . . . . . . .  4
       2.3.  Structure. . . . . . . . . . . . . . . . . . . . . . . .  5
       2.4.  Counters, Interval Buckets and Thresholds. . . . . . . .  7
       2.5.  Profiles . . . . . . . . . . . . . . . . . . . . . . . .  8
       2.6.  Notifications. . . . . . . . . . . . . . . . . . . . . .  9
       2.7.  Persistence. . . . . . . . . . . . . . . . . . . . . . . 10
   3.  Conformance and Compliance . . . . . . . . . . . . . . . . . . 11
   4.  Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . 11
   5.  Security Considerations. . . . . . . . . . . . . . . . . . . . 71
   6.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 72
       6.1.  Normative References . . . . . . . . . . . . . . . . . . 72
       6.2.  Informative References . . . . . . . . . . . . . . . . . 74
   7.  Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 74

   8.  Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 75
   9.  Full Copyright Statement . . . . . . . . . . . . . . . . . . . 76

1.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

2.  Overview

   This document describes an SNMP MIB module for managing VDSL Lines.
   These definitions are based upon the specifications for VDSL as
   defined in T1E1, ETSI, and ITU documentation [T1E1311, T1E1011,
   T1E1013, ETSI2701, ETSI2702, ITU9931, ITU9971].

   The MIB module is located in the MIB tree under MIB 2 transmission,
   as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of
   this document.

2.1.   Relationship of the VDSL Line MIB Module to other MIB Modules

   This section outlines the relationship of this MIB with other MIBs
   described in RFCs.  Specifically, IF-MIB as presented in RFC 2863
   [RFC2863] is discussed.

2.1.1.   General IF-MIB Integration (RFC 2863)

   The VDSL Line MIB specifies the detailed attributes of a data
   interface.  As such, it needs to integrate with RFC 2863 [RFC2863].
   The IANA has assigned the following ifType to VDSL:

   IANAifType ::= TEXTUAL-CONVENTION
       ...

   SYNTAX INTEGER {
       ...
       vdsl(97), -- Very H-speed Digital Subscrib.  Loop
       ...
       }

   Additionally, a VDSL line may contain an optional fast channel and an
   optional interleaved channel which also integrate into RFC 2863
   [RFC2863].  The IANA has assigned the following ifTypes to these
   channels:

   IANAifType ::= TEXTUAL-CONVENTION
       ...
   SYNTAX INTEGER {
       ...
       interleave (124), -- Interleave channel
       fast (125),       -- Fast channel
       ...
       }

2.1.2.  Usage of ifTable

   The MIB branch identified by this ifType contains tables appropriate
   for this interface type.  Most tables extend the ifEntry table, and
   are indexed by ifIndex.  For interfaces in systems implementing this
   MIB, those table entries indexed by ifIndex MUST be persistent.

   The following attributes are part of the mandatory ifGeneral group in
   RFC 2863 [RFC2863], and are not duplicated in the VDSL Line MIB.

   ===================================================================
       ifIndex                  Interface index.

       ifDescr                  See interfaces MIB [RFC2863].

       ifType                   vdsl(97),
                                interleave(124), or
                                fast(125)

       ifSpeed                  Set as appropriate.

       ifPhysAddress            This object MUST have an octet string
                                with zero length.

       ifAdminStatus            See interfaces MIB [RFC2863].

       ifOperStatus             See interfaces MIB [RFC2863].

       ifLastChange             See interfaces MIB [RFC2863].

       ifName                   See interfaces MIB [RFC2863].

       ifHighSpeed              Set as appropriate.

       ifConnectorPresent       Set as appropriate.

       ifLinkUpDownTrapEnable   Default to enabled(1).

   ===================================================================
                   Figure 1: Use of ifTable Objects

   Section 2.3, below, describes the structure of this MIB in relation
   to ifEntry in greater detail.

2.2.  Conventions used in the MIB Module

2.2.1.  Naming Conventions

   A.  Vtuc -- (VTUC) transceiver at near (Central) end of line
   B.  Vtur -- (VTUR) transceiver at Remote end of line
   C.  Vtu  -- One of either Vtuc or Vtur
   D.  Curr -- Current
   E.  Prev -- Previous
   F.  Atn  -- Attenuation
   G.  ES   -- Errored Second
   H.  SES  -- Severely Errored Second
   I.  UAS  -- Unavailable Second
   J.  LCS  -- Line Code Specific
   K.  Lof  -- Loss of Frame
   L.  Lol  -- Loss of Link
   M.  Los  -- Loss of Signal
   N.  Lpr  -- Loss of Power
   O.  xxxs -- Sum of Seconds in which xxx has occured
               (e.g., xxx = Lof, Los, Lpr, Lol)
   P.  Max  -- Maximum
   Q.  Mgn  -- Margin
   R.  Min  -- Minimum
   S.  Psd  -- Power Spectral Density
   T.  Snr  -- Signal to Noise Ratio
   U.  Tx   -- Transmit
   V.  Blks -- Blocks

2.2.2.  Textual Conventions

   The following textual conventions are defined to reflect the line
   topology in the MIB (further discussed in the following section) and
   to define the behavior of the statistics to be maintained by an
   agent.

   o    VdslLineCodingType :

   Attributes with this syntax identify the line coding used.  Specified
   as an INTEGER, the three values are:

   other(1)  -- none of the following
   mcm(2)    -- Multiple Carrier Modulation
   scm(3)    -- Single Carrier Modulation

   o    VdslLineEntity :

   Attributes with this syntax reference the two sides of a line.
   Specified as an INTEGER, the two values are:

   vtuc(1)  -- central site transceiver
   vtur(2)  -- remote site transceiver

2.3  Structure

   The MIB is structured into the following MIB groups:

   o   vdslGroup :

   This group supports all line code independent MIB objects found in
   this MIB.  The following tables contain objects permitted for ifType
   vdsl(97):

      - vdslLineTable
      - vdslPhysTable
      - vdslPerfDataTable
      - vdslPerfIntervalTable
      - vdslPerf1DayIntervalTable
      - vdslLineConfProfileTable
      - vdslLineAlarmConfProfileTable

   The following tables contain objects permitted for ifTypes
   interleave(124) and (fast):

      - vdslChanTable
      - vdslChanPerfDataTable
      - vdslChanPerfIntervalTable
      - vdslChanPerf1DayIntervalTable

   Figure 2, below, displays the relationship of the tables in the
   vdslGroup to ifEntry (and each other):

     ifEntry(ifType=97)  ---> vdslLineTableEntry 1:(0 to 1)

     vdslLineTableEntry  ---> vdslPhysTableEntry 1:(0 to 2)
                         ---> vdslPerfDataEntry 1:(0 to 2)
                         ---> vdslLineConfProfileEntry 1:(0 to 1)
                         ---> vdslLineAlarmConfProfileEntry 1:(0 to 1)

     vdslPhysTableEntry  ---> vdslPerfIntervalEntry 1:(0 to 96)
                         ---> vdslPerf1DayIntervalEntry 1:(0 to 30)

     ifEntry(ifType=124) ---> vdslChanEntry 1:(0 to 2)
                         ---> vdslChanPerfDataEntry 1:(0 to 2)

     ifEntry(ifType=125) ---> vdslChanEntry 1:(0 to 2)
                         ---> vdslChanPerfDataEntry 1:(0 to 2)

     vdslChanEntry       ---> vdslchanPerfIntervalEntry 1:(0 to 96)
                         ---> vdslchan1DayPerfIntervalEntry 1:(0 to 30)

                   Figure 2: Table Relationships

   o   vdslNotificationGroup :

   This group contains definitions of VDSL line notifications.  Section
   2.6, below, presents greater detail on the notifications defined
   within the MIB module.

2.3.1.  Line Topology

   A VDSL Line consists of two units - a Vtuc (the central transceiver
   unit) and a Vtur (the remote transceiver unit).

             <-- Network Side   Customer Side -->

             |<////////// VDSL Line ///////////>|

             +-------+                  +-------+
             |       |                  |       |
             | Vtuc  +------------------+  Vtur |
             |       |                  |       |
             +-------+                  +-------+

          Figure 3: General topology for a VDSL Line

2.4.  Counters, Interval Buckets and Thresholds

   For Loss of Frame (lof), Loss of Link (lol), Loss of Signal (los),
   and Loss of Power (lpr), Errored Seconds (ES), Severely Errored
   Seconds (SES), and Unavailable Seconds (UAS) there are event
   counters, current 15-minute, 0 to 96 15-minute history bucket(s), and
   0 to 30 1-day history bucket(s) of "interval-counters".  Each current
   15-minute event bucket has an associated threshold notification.

   Each of these counters uses the textual conventions defined in the
   HC-PerfHist-TC-MIB [RFC3705].  The HC-PerfHist-TC-MIB defines 64-bit
   versions of the textual conventions found in RFC 3593 [RFC3593].

   There is no requirement for an agent to ensure a fixed relationship
   between the start of a fifteen minute interval and any wall clock;
   however, some implementations may align the fifteen minute intervals
   with quarter hours.  Likewise, an implementation may choose to align
   one day intervals with the start of a day.

   Counters are not reset when a Vtu is reinitialized, only when the
   agent is reset or reinitialized (or under specific request outside
   the scope of this MIB module).

2.5.  Profiles

   As a managed node can handle a large number of Vtus, (e.g., hundreds
   or perhaps thousands of lines), provisioning every parameter on every
   Vtu may become burdensome.  Moreover, most lines are provisioned
   identically with the same set of parameters.  To simplify the
   provisioning process, this MIB makes use of profiles.  A profile is a
   set of parameters that can be shared by multiple lines using the same
   configuration.

   The following profiles are used in this MIB module:

   o   Line Configuration Profiles - Line configuration profiles contain
       parameters for configuring VDSL lines.  They are defined in the
       vdslLineConfProfileTable.

   o   Alarm Configuration Profiles - These profiles contain parameters
       for configuring alarm thresholds for VDSL transceivers.  These
       profiles are defined in the vdslLineAlarmConfProfileTable.

   One or more lines may be configured to share parameters of a single
   profile by setting their vdslLineConfProfile objects to the value of
   this profile.  If a change is made to the profile, all lines that
   refer to it will be reconfigured to the changed parameters.  Before a
   profile can be deleted or taken out of service it must be first
   unreferenced from all associated lines.

   Implementations MUST provide a default profile with an index value of
   'DEFVAL' for each profile type.  The values of the associated
   parameters will be vendor specific unless otherwise indicated in this
   document.  Before a line's profiles have been set, these profiles
   will be automatically used by setting vdslLineConfProfile and
   vdslLineAlarmConfProfile to 'DEFVAL' where appropriate.  This default
   profile name, 'DEFVAL', is considered reserved in the context of
   profiles defined in this MIB module.

   Profiles are created, assigned, and deleted dynamically using the
   profile name and profile row status in each of the ten profile tables
   (nine line configuration tables and one alarm configuration table).

   Profile changes MUST take effect immediately.  These changes MAY
   result in a restart (hard reset or soft restart) of the units on the
   line.

2.6.  Notifications

   The ability to generate the SNMP notifications coldStart/WarmStart
   (per [RFC3418]) which are per agent (e.g., per Digital Subscriber
   Line Access Multiplexer, or DSLAM, in such a device), and
   linkUp/linkDown (per [RFC2863]) which are per interface (i.e., VDSL
   line) is required.

   The notifications defined in this MIB are for initialization failure
   and for the threshold crossings associated with the following events:
   lof, lol, los, lpr, ES, SES, and UAS.  Each threshold has its own
   enable/threshold value.  When that value is 0, the notification is
   disabled.

   A linkDown notification MAY be generated whenever any of lof, lol,
   los, lpr, ES, SES, or UAS threshold crossing event (as defined in
   this MIB module) occurs.  The corresponding linkUp notification MAY
   be sent when all link failure conditions are cleared.

   The vdslPhysCurrStatus is a bitmask representing all outstanding
   error conditions associated with a particular VDSL transceiver.  Note
   that since status of remote transceivers is obtained via the EOC,
   this information may be unavailable for units that are unreachable
   via the EOC during a line error condition.  Therefore, not all
   conditions may always be included in its current status.
   Notifications corresponding to the bit fields in this object are
   defined.

   A threshold notification occurs whenever the corresponding current
   15-minute interval error counter becomes equal to, or exceeds the
   threshold value.  One notification may be sent per interval per
   interface.  Since the current 15-minute counters are reset to 0 every
   15 minutes, if the condition persists, the notification may recur as
   often as every 15 minutes.  For example, to get a notification
   whenever a "loss of" event occurs (but at most once every 15
   minutes), set the corresponding threshold to 1.  The agent will
   generate a notification when the event originally occurs.

   Note that the Network Management System, or NMS, may receive a
   linkDown notification, as well, if enabled (via
   ifLinkUpDownTrapEnable [RFC2863]).  At the beginning of the next 15
   minute interval, the counter is reset.  When the first second goes by
   and the event occurs, the current interval bucket will be 1, which
   equals the threshold and the notification will be sent again.

2.7.  Persistence

   All read-write and read-create objects defined in this MIB module
   SHOULD be stored persistently.  Following is an exhaustive list of
   these persistent objects:

      - vdslLineConfProfile
      - vdslLineAlarmConfProfile
      - vdslLineConfProfileName
      - vdslLineConfDownRateMode
      - vdslLineConfUpRateMode
      - vdslLineConfDownMaxPwr
      - vdslLineConfUpMaxPwr
      - vdslLineConfDownMaxSnrMgn
      - vdslLineConfDownMinSnrMgn
      - vdslLineConfDownTargetSnrMgn
      - vdslLineConfUpMaxSnrMgn
      - vdslLineConfUpMinSnrMgn
      - vdslLineConfUpTargetSnrMgn
      - vdslLineConfDownFastMaxDataRate
      - vdslLineConfDownFastMinDataRate
      - vdslLineConfDownSlowMaxDataRate
      - vdslLineConfDownSlowMinDataRate
      - vdslLineConfUpFastMaxDataRate
      - vdslLineConfUpFastMinDataRate
      - vdslLineConfUpSlowMaxDataRate
      - vdslLineConfUpSlowMinDataRate
      - vdslLineConfDownRateRatio
      - vdslLineConfUpRateRatio
      - vdslLineConfDownMaxInterDelay
      - vdslLineConfUpMaxInterDelay
      - vdslLineConfDownPboControl
      - vdslLineConfUpPboControl
      - vdslLineConfDownPboLevel
      - vdslLineConfUpPboLevel
      - vdslLineConfDeploymentScenario
      - vdslLineConfAdslPresence
      - vdslLineConfApplicableStandard
      - vdslLineConfBandPlan
      - vdslLineConfBandPlanFx
      - vdslLineConfBandOptUsage
      - vdslLineConfUpPsdTemplate
      - vdslLineConfDownPsdTemplate
      - vdslLineConfHamBandMask
      - vdslLineConfCustomNotch1Start
      - vdslLineConfCustomNotch1Stop
      - vdslLineConfCustomNotch2Start
      - vdslLineConfCustomNotch2Stop

      - vdslLineConfDownTargetSlowBurst
      - vdslLineConfUpTargetSlowBurst
      - vdslLineConfDownMaxFastFec
      - vdslLineConfUpMaxFastFec
      - vdslLineConfLineType
      - vdslLineConfProfRowStatus
      - vdslLineAlarmConfProfileName
      - vdslLineAlarmConfThresh15MinLofs
      - vdslLineAlarmConfThresh15MinLoss
      - vdslLineAlarmConfThresh15MinLprs
      - vdslLineAlarmConfThresh15MinLols
      - vdslLineAlarmConfThresh15MinESs
      - vdslLineAlarmConfThresh15MinSESs
      - vdslLineAlarmConfThresh15MinUASs
      - vdslLineAlarmConfInitFailure
      - vdslLineAlarmConfProfRowStatus

   It should also be noted that interface indices in this MIB are
   maintained persistently.  VACM data relating to these SHOULD be
   stored persistently as well [RFC3415].

3.  Conformance and Compliance

   For VDSL lines, the following groups are mandatory:

      -  vdslGroup
      -  vdslNotificationGroup

4.  Definitions

EID 1791 (Verified) is as follows:

Section: 4

Original Text:

UNITS definition of the following MIB objects, should change from dBm to dB.
That will also fix the conflict with the units appearing in the Description of these MIB objects (dB).

vdslPhysCurrSnrMgn
vdslPhysCurrAtn
vdslLineConfDownMaxSnrMgn
vdslLineConfDownMinSnrMgn
vdslLineConfDownTargetSnrMgn
vdslLineConfUpMaxSnrMgn
vdslLineConfUpMinSnrMgn
vdslLineConfUpTargetSnrMgn

Example of original text:
   vdslPhysCurrSnrMgn OBJECT-TYPE
       SYNTAX       Integer32 (-127..127)
       UNITS        "0.25dBm"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           "Noise Margin as seen by this Vtu with respect to its
           received signal in 0.25dB.  The effective range is
           -31.75 to +31.75 dB."
       REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
        ::= { vdslPhysEntry 5 }

Corrected Text:

Example of corrected text:
   vdslPhysCurrSnrMgn OBJECT-TYPE
       SYNTAX       Integer32 (-127..127)
       UNITS        "0.25dB"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           "Noise Margin as seen by this Vtu with respect to its
           received signal in 0.25dB.  The effective range is
           -31.75 to +31.75 dB."
       REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
        ::= { vdslPhysEntry 5 }
Notes:
This Errata replaces errata 1788 (rejected because it did not include list of all MIB objects having this problem and could not be edited).
It was decided by the adslmib Forum, that the solution should be as described by this Errata.
VDSL-LINE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Gauge32, Integer32, Unsigned32, NOTIFICATION-TYPE, transmission FROM SNMPv2-SMI -- [RFC2578] ZeroBasedCounter64 FROM HCNUM-TC -- [RFC2856] TEXTUAL-CONVENTION, RowStatus, TruthValue FROM SNMPv2-TC -- [RFC2579] HCPerfValidIntervals, HCPerfInvalidIntervals, HCPerfTimeElapsed, HCPerfIntervalThreshold, HCPerfCurrentCount, HCPerfIntervalCount FROM HC-PerfHist-TC-MIB -- [RFC3705] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] ifIndex FROM IF-MIB -- [RFC2863] SnmpAdminString FROM SNMP-FRAMEWORK-MIB; -- [RFC3411] vdslMIB MODULE-IDENTITY LAST-UPDATED "200402190000Z" -- February 19, 2004 ORGANIZATION "ADSLMIB Working Group" CONTACT-INFO "WG-email: adslmib@ietf.org Info: https://www1.ietf.org/mailman/listinfo/adslmib Chair: Mike Sneed Sand Channel Systems Postal: P.O. Box 37324 Raleigh, NC 27627-7324 USA Email: sneedmike@hotmail.com Phone: +1 206 600 7022 Co-editor: Bob Ray PESA Switching Systems, Inc. Postal: 330-A Wynn Drive Huntsville, AL 35805 USA Email: rray@pesa.com Phone: +1 256 726 9200 ext. 142 Co-editor: Rajesh Abbi Alcatel USA Postal: 2301 Sugar Bush Road Raleigh, NC 27612-3339 USA Email: Rajesh.Abbi@alcatel.com Phone: +1 919 850 6194 " DESCRIPTION "The MIB module defining objects for the management of a pair of VDSL transceivers at each end of the VDSL line. Each such line has an entry in an ifTable which may include multiple transceiver lines. An agent may reside at either end of the VDSL line. However, the MIB is designed to require no management communication between them beyond that inherent in the low-level VDSL line protocol. The agent may monitor and control this protocol for its needs. VDSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus a VDSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to vdsl(97), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Vtuc -- (VTUC) transceiver at near (Central) end of line Vtur -- (VTUR) transceiver at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. SES -- Severely Errored Second UAS -- Unavailable Second LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs -- Sum of Seconds in which xxx has occured (e.g., xxx = Lof, Los, Lpr, Lol) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks -- Blocks Copyright (C) The Internet Society (2004). This version of this MIB module is part of RFC 3728: see the RFC itself for full legal notices." REVISION "200402190000Z" -- February 19, 2004 DESCRIPTION "Initial version, published as RFC 3728." ::= { transmission 97 } vdslLineMib OBJECT IDENTIFIER ::= { vdslMIB 1 } vdslMibObjects OBJECT IDENTIFIER ::= { vdslLineMib 1 } -- -- textual conventions used in this MIB -- VdslLineCodingType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used as the syntax for the VDSL Line Code. Attributes with this syntax identify the line coding used. Specified as an INTEGER, the three values are: other(1) -- none of the following mcm(2) -- Multiple Carrier Modulation scm(3) -- Single Carrier Modulation" SYNTAX INTEGER { other(1), mcm(2), scm(3) } VdslLineEntity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Identifies a transceiver as being either Vtuc or Vtur. A VDSL line consists of two transceivers, a Vtuc and a Vtur. Attributes with this syntax reference the two sides of a line. Specified as an INTEGER, the two values are: vtuc(1) -- central site transceiver vtur(2) -- remote site transceiver" SYNTAX INTEGER { vtuc(1), vtur(2) } -- -- objects -- vdslLineTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes common attributes describing both ends of the line. It is required for all VDSL physical interfaces. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97)." ::= { vdslMibObjects 1 } vdslLineEntry OBJECT-TYPE SYNTAX VdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslLineTable." INDEX { ifIndex } ::= { vdslLineTable 1 } VdslLineEntry ::= SEQUENCE { vdslLineCoding VdslLineCodingType, vdslLineType INTEGER, vdslLineConfProfile SnmpAdminString, vdslLineAlarmConfProfile SnmpAdminString } vdslLineCoding OBJECT-TYPE SYNTAX VdslLineCodingType MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the VDSL coding type used on this line." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslLineEntry 1 } vdslLineType OBJECT-TYPE SYNTAX INTEGER { noChannel(1), -- no channels exist fastOnly(2), -- only fast channel exists interleavedOnly(3), -- only interleaved channel exists fastOrInterleaved(4), -- either fast or interleaved channel -- exist, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of VDSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. Defined values are: noChannel(1) -- no channels exist fastOnly(2) -- only fast channel exists interleavedOnly(3) -- only interleaved channel exists fastOrInterleaved(4) -- either fast or interleaved channel -- exist, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist Note that 'slow' and 'interleaved' refer to the same channel. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s)." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslLineEntry 2 } vdslLineConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the VDSL Line Configuration Profile Table, vdslLineConfProfileTable, which applies for this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner." DEFVAL { "DEFVAL" } ::= { vdslLineEntry 3 } vdslLineAlarmConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the VDSL Line Alarm Configuration Profile Table, vdslLineAlarmConfProfileTable, which applies to this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner." DEFVAL { "DEFVAL" } ::= { vdslLineEntry 4 } vdslPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu. Each row contains the Physical Layer Parameters table for that Vtu. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97)." ::= { vdslMibObjects 2 } vdslPhysEntry OBJECT-TYPE SYNTAX VdslPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslPhysTable." INDEX { ifIndex, vdslPhysSide } ::= { vdslPhysTable 1 } VdslPhysEntry ::= SEQUENCE { vdslPhysSide VdslLineEntity, vdslPhysInvSerialNumber SnmpAdminString, vdslPhysInvVendorID SnmpAdminString, vdslPhysInvVersionNumber SnmpAdminString, vdslPhysCurrSnrMgn Integer32, vdslPhysCurrAtn Gauge32, vdslPhysCurrStatus BITS, vdslPhysCurrOutputPwr Integer32, vdslPhysCurrAttainableRate Gauge32, vdslPhysCurrLineRate Gauge32 } vdslPhysSide OBJECT-TYPE SYNTAX VdslLineEntity MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies whether the transceiver is the Vtuc or Vtur." ::= { vdslPhysEntry 1 } vdslPhysInvSerialNumber OBJECT-TYPE SYNTAX SnmpAdminString(SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific string that identifies the vendor equipment." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPhysEntry 2 } vdslPhysInvVendorID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor ID code is a copy of the binary vendor identification field expressed as readable characters in hexadecimal notation." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPhysEntry 3 } vdslPhysInvVersionNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific version number sent by this Vtu as part of the initialization messages. It is a copy of the binary version number field expressed as readable characters in hexadecimal notation." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPhysEntry 4 } vdslPhysCurrSnrMgn OBJECT-TYPE SYNTAX Integer32 (-127..127) UNITS "0.25dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this Vtu with respect to its received signal in 0.25dB. The effective range is -31.75 to +31.75 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPhysEntry 5 } vdslPhysCurrAtn OBJECT-TYPE SYNTAX Gauge32 (0..255) UNITS "0.25dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer Vtu and the total power received by this Vtu. The effective range is 0 to +63.75 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPhysEntry 6 } vdslPhysCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4), lossOfLink(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8), noPeerVtuPresent(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state of the Vtu line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There are no defects on the line. 1 lossOfFraming Vtu failure due to not receiving a valid frame. 2 lossOfSignal Vtu failure due to not receiving signal. 3 lossOfPower Vtu failure due to loss of power. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink Vtu failure due to inability to link with peer Vtu. Set whenever the transceiver is in the 'Warm Start' state. 6 dataInitFailure Vtu failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure Vtu failure during initialization due to peer Vtu not able to support requested configuration. 8 protocolInitFailure Vtu failure during initialization due to incompatible protocol used by the peer Vtu. 9 noPeerVtuPresent Vtu failure during initialization due to no activation sequence detected from peer Vtu. This is intended to supplement ifOperStatus." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPhysEntry 7 } vdslPhysCurrOutputPwr OBJECT-TYPE SYNTAX Integer32 (0..160) UNITS "0.1dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this VTU. This is the measurement that was reported during the last activation sequence." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPhysEntry 8 } vdslPhysCurrAttainableRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate in steps of 1000 bits/second by the Vtu. This value will be equal to or greater than vdslPhysCurrLineRate. Note that for SCM, the minimum and maximum data rates are equal. Note: 1 kbps = 1000 bps." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPhysEntry 9 } vdslPhysCurrLineRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current data rate in steps of 1000 bits/second by the Vtu. This value will be less than or equal to vdslPhysCurrAttainableRate. Note: 1 kbps = 1000 bps." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPhysEntry 10 } vdslChanTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125)." ::= { vdslMibObjects 3 } vdslChanEntry OBJECT-TYPE SYNTAX VdslChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslChanTable." INDEX { ifIndex, vdslPhysSide } ::= { vdslChanTable 1 } VdslChanEntry ::= SEQUENCE { vdslChanInterleaveDelay Gauge32, vdslChanCrcBlockLength Gauge32, vdslChanCurrTxRate Gauge32, vdslChanCurrTxSlowBurstProtect Gauge32, vdslChanCurrTxFastFec Gauge32 } vdslChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Interleave Delay for this channel. Interleave delay applies only to the interleave (slow) channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is fast(125), return a value of zero." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanEntry 1 } vdslChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanEntry 2 } vdslChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit data rate on this channel. Note: 1 kbps = 1000 bps." ::= { vdslChanEntry 3 } vdslChanCurrTxSlowBurstProtect OBJECT-TYPE SYNTAX Gauge32 (0..1275) UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual level of impulse noise (burst) protection for an interleaved (slow) channel. This parameter is not applicable to fast channels. For fast channels, a value of zero shall be returned." REFERENCE "ITU-T G.997.1, section 7.3.2.3" ::= { vdslChanEntry 4 } vdslChanCurrTxFastFec OBJECT-TYPE SYNTAX Gauge32 (0..50) UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Forward Error Correction (FEC) redundancy related overhead for a fast channel. This parameter is not applicable to an interleaved (slow) channel. For interleaved channels, a value of zero shall be returned." ::= { vdslChanEntry 5 } vdslPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each VDSL physical interface. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97)." ::= { vdslMibObjects 4 } vdslPerfDataEntry OBJECT-TYPE SYNTAX VdslPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslPerfDataTable." INDEX { ifIndex, vdslPhysSide } ::= { vdslPerfDataTable 1 } VdslPerfDataEntry ::= SEQUENCE { vdslPerfDataValidIntervals HCPerfValidIntervals, vdslPerfDataInvalidIntervals HCPerfInvalidIntervals, vdslPerfDataLofs Unsigned32, vdslPerfDataLoss Unsigned32, vdslPerfDataLprs Unsigned32, vdslPerfDataLols Unsigned32, vdslPerfDataESs Unsigned32, vdslPerfDataSESs Unsigned32, vdslPerfDataUASs Unsigned32, vdslPerfDataInits Unsigned32, vdslPerfDataCurr15MinTimeElapsed HCPerfTimeElapsed, vdslPerfDataCurr15MinLofs HCPerfCurrentCount, vdslPerfDataCurr15MinLoss HCPerfCurrentCount, vdslPerfDataCurr15MinLprs HCPerfCurrentCount, vdslPerfDataCurr15MinLols HCPerfCurrentCount, vdslPerfDataCurr15MinESs HCPerfCurrentCount, vdslPerfDataCurr15MinSESs HCPerfCurrentCount, vdslPerfDataCurr15MinUASs HCPerfCurrentCount, vdslPerfDataCurr15MinInits HCPerfCurrentCount, vdslPerfData1DayValidIntervals HCPerfValidIntervals, vdslPerfData1DayInvalidIntervals HCPerfInvalidIntervals, vdslPerfDataCurr1DayTimeElapsed HCPerfTimeElapsed, vdslPerfDataCurr1DayLofs Unsigned32, vdslPerfDataCurr1DayLoss Unsigned32, vdslPerfDataCurr1DayLprs Unsigned32, vdslPerfDataCurr1DayLols Unsigned32, vdslPerfDataCurr1DayESs Unsigned32, vdslPerfDataCurr1DaySESs Unsigned32, vdslPerfDataCurr1DayUASs Unsigned32, vdslPerfDataCurr1DayInits Unsigned32 } vdslPerfDataValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { vdslPerfDataEntry 1 } vdslPerfDataInvalidIntervals OBJECT-TYPE SYNTAX HCPerfInvalidIntervals UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Invalid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { vdslPerfDataEntry 2 } vdslPerfDataLofs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds since the unit was last reset that there was Loss of Framing." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 3 } vdslPerfDataLoss OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds since the unit was last reset that there was Loss of Signal." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 4 } vdslPerfDataLprs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds since the unit was last reset that there was Loss of Power." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 5 } vdslPerfDataLols OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds since the unit was last reset that there was Loss of Link." ::= { vdslPerfDataEntry 6 } vdslPerfDataESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds since the unit was last reset. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 7 } vdslPerfDataSESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds since the unit was last reset." ::= { vdslPerfDataEntry 8 } vdslPerfDataUASs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds since the unit was last reset." ::= { vdslPerfDataEntry 9 } vdslPerfDataInits OBJECT-TYPE SYNTAX Unsigned32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts since the unit was last reset. This count includes both successful and failed attempts." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 10 } vdslPerfDataCurr15MinTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { vdslPerfDataEntry 11 } vdslPerfDataCurr15MinLofs OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds during this interval that there was Loss of Framing." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 12 } vdslPerfDataCurr15MinLoss OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds during this interval that there was Loss of Signal." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 13 } vdslPerfDataCurr15MinLprs OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds during this interval that there was Loss of Power." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 14 } vdslPerfDataCurr15MinLols OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds during this interval that there was Loss of Link." ::= { vdslPerfDataEntry 15 } vdslPerfDataCurr15MinESs OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during this interval. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 16 } vdslPerfDataCurr15MinSESs OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds during this interval." ::= { vdslPerfDataEntry 17 } vdslPerfDataCurr15MinUASs OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds during this interval." ::= { vdslPerfDataEntry 18 } vdslPerfDataCurr15MinInits OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts during this interval. This count includes both successful and failed attempts." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfDataEntry 19 } vdslPerfData1DayValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { vdslPerfDataEntry 20 } vdslPerfData1DayInvalidIntervals OBJECT-TYPE SYNTAX HCPerfInvalidIntervals UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Invalid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { vdslPerfDataEntry 21 } vdslPerfDataCurr1DayTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { vdslPerfDataEntry 22 } vdslPerfDataCurr1DayLofs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Framing (LOF) Seconds since the beginning of the current 1-day interval." ::= { vdslPerfDataEntry 23 } vdslPerfDataCurr1DayLoss OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Signal (LOS) Seconds since the beginning of the current 1-day interval." ::= { vdslPerfDataEntry 24 } vdslPerfDataCurr1DayLprs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Power (LPR) Seconds since the beginning of the current 1-day interval." ::= { vdslPerfDataEntry 25 } vdslPerfDataCurr1DayLols OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Link (LOL) Seconds since the beginning of the current 1-day interval." ::= { vdslPerfDataEntry 26 } vdslPerfDataCurr1DayESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) since the beginning of the current 1-day interval." ::= { vdslPerfDataEntry 27 } vdslPerfDataCurr1DaySESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) since the beginning of the current 1-day interval." ::= { vdslPerfDataEntry 28 } vdslPerfDataCurr1DayUASs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) since the beginning of the current 1-day interval." ::= { vdslPerfDataEntry 29 } vdslPerfDataCurr1DayInits OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts since the beginning of the current 1-day interval. This count includes both successful and failed attempts." ::= { vdslPerfDataEntry 30 } vdslPerfIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu performance data collection interval. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97)." ::= { vdslMibObjects 5 } vdslPerfIntervalEntry OBJECT-TYPE SYNTAX VdslPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslPerfIntervalTable." INDEX { ifIndex, vdslPhysSide, vdslPerfIntervalNumber } ::= { vdslPerfIntervalTable 1 } VdslPerfIntervalEntry ::= SEQUENCE { vdslPerfIntervalNumber Unsigned32, vdslPerfIntervalLofs HCPerfIntervalCount, vdslPerfIntervalLoss HCPerfIntervalCount, vdslPerfIntervalLprs HCPerfIntervalCount, vdslPerfIntervalLols HCPerfIntervalCount, vdslPerfIntervalESs HCPerfIntervalCount, vdslPerfIntervalSESs HCPerfIntervalCount, vdslPerfIntervalUASs HCPerfIntervalCount, vdslPerfIntervalInits HCPerfIntervalCount } vdslPerfIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional." ::= { vdslPerfIntervalEntry 1 } vdslPerfIntervalLofs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfIntervalEntry 2 } vdslPerfIntervalLoss OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfIntervalEntry 3 } vdslPerfIntervalLprs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfIntervalEntry 4 } vdslPerfIntervalLols OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link." ::= { vdslPerfIntervalEntry 5 } vdslPerfIntervalESs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) in the interval. An Errored Second is a one-second interval containing one or more CRC anomalies, one or more LOS or LOF defects." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfIntervalEntry 6 } vdslPerfIntervalSESs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds in the interval." ::= { vdslPerfIntervalEntry 7 } vdslPerfIntervalUASs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds in the interval." ::= { vdslPerfIntervalEntry 8 } vdslPerfIntervalInits OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts during this interval. This count includes both successful and failed attempts." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerfIntervalEntry 9 } vdslPerf1DayIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent." ::= { vdslMibObjects 6 } vdslPerf1DayIntervalEntry OBJECT-TYPE SYNTAX VdslPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslPerf1DayIntervalTable." INDEX { ifIndex, vdslPhysSide, vdslPerf1DayIntervalNumber } ::= { vdslPerf1DayIntervalTable 1 } VdslPerf1DayIntervalEntry ::= SEQUENCE { vdslPerf1DayIntervalNumber Unsigned32, vdslPerf1DayIntervalMoniSecs HCPerfTimeElapsed, vdslPerf1DayIntervalLofs Unsigned32, vdslPerf1DayIntervalLoss Unsigned32, vdslPerf1DayIntervalLprs Unsigned32, vdslPerf1DayIntervalLols Unsigned32, vdslPerf1DayIntervalESs Unsigned32, vdslPerf1DayIntervalSESs Unsigned32, vdslPerf1DayIntervalUASs Unsigned32, vdslPerf1DayIntervalInits Unsigned32 } vdslPerf1DayIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..30) MAX-ACCESS not-accessible STATUS current DESCRIPTION "History Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional." ::= { vdslPerf1DayIntervalEntry 1 } vdslPerf1DayIntervalMoniSecs OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { vdslPerf1DayIntervalEntry 2 } vdslPerf1DayIntervalLofs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Frame (LOF) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerf1DayIntervalEntry 3 } vdslPerf1DayIntervalLoss OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Signal (LOS) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerf1DayIntervalEntry 4 } vdslPerf1DayIntervalLprs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Power (LPR) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerf1DayIntervalEntry 5 } vdslPerf1DayIntervalLols OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Link (LOL) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." ::= { vdslPerf1DayIntervalEntry 6 } vdslPerf1DayIntervalESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerf1DayIntervalEntry 7 } vdslPerf1DayIntervalSESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." ::= { vdslPerf1DayIntervalEntry 8 } vdslPerf1DayIntervalUASs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." ::= { vdslPerf1DayIntervalEntry 9 } vdslPerf1DayIntervalInits OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs. This count includes both successful and failed attempts." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslPerf1DayIntervalEntry 10 } vdslChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125)." ::= { vdslMibObjects 7 } vdslChanPerfDataEntry OBJECT-TYPE SYNTAX VdslChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslChanPerfDataTable." INDEX { ifIndex, vdslPhysSide } ::= { vdslChanPerfDataTable 1 } VdslChanPerfDataEntry ::= SEQUENCE { vdslChanValidIntervals HCPerfValidIntervals, vdslChanInvalidIntervals HCPerfInvalidIntervals, vdslChanFixedOctets ZeroBasedCounter64, vdslChanBadBlks ZeroBasedCounter64, vdslChanCurr15MinTimeElapsed HCPerfTimeElapsed, vdslChanCurr15MinFixedOctets HCPerfCurrentCount, vdslChanCurr15MinBadBlks HCPerfCurrentCount, vdslChan1DayValidIntervals HCPerfValidIntervals, vdslChan1DayInvalidIntervals HCPerfInvalidIntervals, vdslChanCurr1DayTimeElapsed HCPerfTimeElapsed, vdslChanCurr1DayFixedOctets HCPerfCurrentCount, vdslChanCurr1DayBadBlks HCPerfCurrentCount } vdslChanValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { vdslChanPerfDataEntry 1 } vdslChanInvalidIntervals OBJECT-TYPE SYNTAX HCPerfInvalidIntervals UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Invalid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { vdslChanPerfDataEntry 2 } vdslChanFixedOctets OBJECT-TYPE SYNTAX ZeroBasedCounter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets since the unit was last reset." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanPerfDataEntry 3 } vdslChanBadBlks OBJECT-TYPE SYNTAX ZeroBasedCounter64 UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks since the unit was last reset." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanPerfDataEntry 4 } vdslChanCurr15MinTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { vdslChanPerfDataEntry 5 } vdslChanCurr15MinFixedOctets OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanPerfDataEntry 6 } vdslChanCurr15MinBadBlks OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanPerfDataEntry 7 } vdslChan1DayValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { vdslChanPerfDataEntry 8 } vdslChan1DayInvalidIntervals OBJECT-TYPE SYNTAX HCPerfInvalidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "Invalid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { vdslChanPerfDataEntry 9 } vdslChanCurr1DayTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { vdslChanPerfDataEntry 10 } vdslChanCurr1DayFixedOctets OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets since the beginning of the current 1-day interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanPerfDataEntry 11 } vdslChanCurr1DayBadBlks OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks since the beginning of the current 1-day interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanPerfDataEntry 12 } vdslChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu channel data collection interval. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125)." ::= { vdslMibObjects 8 } vdslChanIntervalEntry OBJECT-TYPE SYNTAX VdslChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslChanIntervalTable." INDEX { ifIndex, vdslPhysSide, vdslChanIntervalNumber } ::= { vdslChanIntervalTable 1 } VdslChanIntervalEntry ::= SEQUENCE { vdslChanIntervalNumber Unsigned32, vdslChanIntervalFixedOctets HCPerfIntervalCount, vdslChanIntervalBadBlks HCPerfIntervalCount } vdslChanIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional." ::= { vdslChanIntervalEntry 1 } vdslChanIntervalFixedOctets OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanIntervalEntry 2 } vdslChanIntervalBadBlks OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChanIntervalEntry 3 } vdslChan1DayIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslChan1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent." ::= { vdslMibObjects 9 } vdslChan1DayIntervalEntry OBJECT-TYPE SYNTAX VdslChan1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslChan1DayIntervalTable." INDEX { ifIndex, vdslPhysSide, vdslChan1DayIntervalNumber } ::= { vdslChan1DayIntervalTable 1 } VdslChan1DayIntervalEntry ::= SEQUENCE { vdslChan1DayIntervalNumber Unsigned32, vdslChan1DayIntervalMoniSecs HCPerfTimeElapsed, vdslChan1DayIntervalFixedOctets HCPerfCurrentCount, vdslChan1DayIntervalBadBlks HCPerfCurrentCount } vdslChan1DayIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..30) MAX-ACCESS not-accessible STATUS current DESCRIPTION "History Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional." ::= { vdslChan1DayIntervalEntry 1 } vdslChan1DayIntervalMoniSecs OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { vdslChan1DayIntervalEntry 2 } vdslChan1DayIntervalFixedOctets OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChan1DayIntervalEntry 3 } vdslChan1DayIntervalBadBlks OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { vdslChan1DayIntervalEntry 4 } -- -- profile tables -- vdslLineConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the VDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. Entries in this table MUST be maintained in a persistent manner." ::= { vdslMibObjects 11 } vdslLineConfProfileEntry OBJECT-TYPE SYNTAX VdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of a VDSL line. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document." INDEX { vdslLineConfProfileName } ::= { vdslLineConfProfileTable 1 } VdslLineConfProfileEntry ::= SEQUENCE { vdslLineConfProfileName SnmpAdminString, vdslLineConfDownRateMode INTEGER, vdslLineConfUpRateMode INTEGER, vdslLineConfDownMaxPwr Unsigned32, vdslLineConfUpMaxPwr Unsigned32, vdslLineConfDownMaxSnrMgn Unsigned32, vdslLineConfDownMinSnrMgn Unsigned32, vdslLineConfDownTargetSnrMgn Unsigned32, vdslLineConfUpMaxSnrMgn Unsigned32, vdslLineConfUpMinSnrMgn Unsigned32, vdslLineConfUpTargetSnrMgn Unsigned32, vdslLineConfDownFastMaxDataRate Unsigned32, vdslLineConfDownFastMinDataRate Unsigned32, vdslLineConfDownSlowMaxDataRate Unsigned32, vdslLineConfDownSlowMinDataRate Unsigned32, vdslLineConfUpFastMaxDataRate Unsigned32, vdslLineConfUpFastMinDataRate Unsigned32, vdslLineConfUpSlowMaxDataRate Unsigned32, vdslLineConfUpSlowMinDataRate Unsigned32, vdslLineConfDownRateRatio Unsigned32, vdslLineConfUpRateRatio Unsigned32, vdslLineConfDownMaxInterDelay Unsigned32, vdslLineConfUpMaxInterDelay Unsigned32, vdslLineConfDownPboControl INTEGER, vdslLineConfUpPboControl INTEGER, vdslLineConfDownPboLevel Unsigned32, vdslLineConfUpPboLevel Unsigned32, vdslLineConfDeploymentScenario INTEGER, vdslLineConfAdslPresence INTEGER, vdslLineConfApplicableStandard INTEGER, vdslLineConfBandPlan INTEGER, vdslLineConfBandPlanFx Unsigned32, vdslLineConfBandOptUsage INTEGER, vdslLineConfUpPsdTemplate INTEGER, vdslLineConfDownPsdTemplate INTEGER, vdslLineConfHamBandMask BITS, vdslLineConfCustomNotch1Start Unsigned32, vdslLineConfCustomNotch1Stop Unsigned32, vdslLineConfCustomNotch2Start Unsigned32, vdslLineConfCustomNotch2Stop Unsigned32, vdslLineConfDownTargetSlowBurst Unsigned32, vdslLineConfUpTargetSlowBurst Unsigned32, vdslLineConfDownMaxFastFec Unsigned32, vdslLineConfUpMaxFastFec Unsigned32, vdslLineConfLineType INTEGER, vdslLineConfProfRowStatus RowStatus } vdslLineConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies a row in this table. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document." ::= { vdslLineConfProfileEntry 1 } vdslLineConfDownRateMode OBJECT-TYPE SYNTAX INTEGER { manual(1), adaptAtInit(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the rate selection behavior for the line in the downstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line based upon line quality." DEFVAL { adaptAtInit } ::= { vdslLineConfProfileEntry 2 } vdslLineConfUpRateMode OBJECT-TYPE SYNTAX INTEGER { manual(1), adaptAtInit(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the rate selection behavior for the line in the upstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line based upon line quality." DEFVAL { adaptAtInit } ::= { vdslLineConfProfileEntry 3 } vdslLineConfDownMaxPwr OBJECT-TYPE SYNTAX Unsigned32 (0..58) UNITS "0.25dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum aggregate downstream power level in the range 0 to 14.5 dBm." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 4 } vdslLineConfUpMaxPwr OBJECT-TYPE SYNTAX Unsigned32 (0..58) UNITS "0.25dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum aggregate upstream power level in the range 0 to 14.5 dBm." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 5 } vdslLineConfDownMaxSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..127) UNITS "0.25dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 6 } vdslLineConfDownMinSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..127) UNITS "0.25dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 7 } vdslLineConfDownTargetSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..127) UNITS "0.25dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the target downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 8 } vdslLineConfUpMaxSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..127) UNITS "0.25dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 9 } vdslLineConfUpMinSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..127) UNITS "0.25dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 10 } vdslLineConfUpTargetSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..127) UNITS "0.25dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the target upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 11 } vdslLineConfDownFastMaxDataRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum downstream fast channel data rate in steps of 1000 bits/second." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 12 } vdslLineConfDownFastMinDataRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum downstream fast channel data rate in steps of 1000 bits/second." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 13 } vdslLineConfDownSlowMaxDataRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum downstream slow channel data rate in steps of 1000 bits/second. The maximum aggregate downstream transmit speed of the line can be derived from the sum of maximum downstream fast and slow channel data rates." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 14 } vdslLineConfDownSlowMinDataRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum downstream slow channel data rate in steps of 1000 bits/second. The minimum aggregate downstream transmit speed of the line can be derived from the sum of minimum downstream fast and slow channel data rates." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 15 } vdslLineConfUpFastMaxDataRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum upstream fast channel data rate in steps of 1000 bits/second. The maximum aggregate upstream transmit speed of the line can be derived from the sum of maximum upstream fast and slow channel data rates." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 16 } vdslLineConfUpFastMinDataRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum upstream fast channel data rate in steps of 1000 bits/second. The minimum aggregate upstream transmit speed of the line can be derived from the sum of minimum upstream fast and slow channel data rates." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 17 } vdslLineConfUpSlowMaxDataRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum upstream slow channel data rate in steps of 1000 bits/second." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 18 } vdslLineConfUpSlowMinDataRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum upstream slow channel data rate in steps of 1000 bits/second." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 19 } vdslLineConfDownRateRatio OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "For dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents downstream Fast Channel Allocation / Slow Channel Allocation." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 20 } vdslLineConfUpRateRatio OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "For dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents upstream Fast Channel Allocation/Slow Channel Allocation." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 21 } vdslLineConfDownMaxInterDelay OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum interleave delay for the downstream slow channel." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 22 } vdslLineConfUpMaxInterDelay OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum interleave delay for the upstream slow channel." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 23 } vdslLineConfDownPboControl OBJECT-TYPE SYNTAX INTEGER { disabled(1), auto(2), manual(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Downstream power backoff (PBO) control for this line. For transceivers which do not support downstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from vdslLineConfDownPboLevel." DEFVAL { disabled } ::= { vdslLineConfProfileEntry 24 } vdslLineConfUpPboControl OBJECT-TYPE SYNTAX INTEGER { disabled(1), auto(2), manual(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff (PBO) control for this line. For transceivers which do not support upstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from vdslLineConfUpPboLevel." DEFVAL { disabled } ::= { vdslLineConfProfileEntry 25 } vdslLineConfDownPboLevel OBJECT-TYPE SYNTAX Unsigned32 (0..160) UNITS "0.25dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the downstream backoff level to be used when vdslLineConfDownPboControl = manual(3)." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 26 } vdslLineConfUpPboLevel OBJECT-TYPE SYNTAX Unsigned32 (0..160) UNITS "0.25dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the upstream backoff level to be used when vdslLineConfUpPboControl = manual(3)." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 27 } vdslLineConfDeploymentScenario OBJECT-TYPE SYNTAX INTEGER { fttCab(1), fttEx(2), other(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The VDSL line deployment scenario. When using fttCab(1), the VTU-C is located in a street cabinet. When using fttEx(2), the VTU-C is located at the central office. Changes to this value will have no effect on the transceiver." REFERENCE "DSL Forum TR-057" DEFVAL { fttCab } ::= { vdslLineConfProfileEntry 28 } vdslLineConfAdslPresence OBJECT-TYPE SYNTAX INTEGER { none(1), adslOverPots(2), adslOverISDN(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates presence of ADSL service in the associated cable bundle/binder. none(1) indicates no ADSL service in the bundle adslOverPots(2) indicates ADSL service over POTS is present in the bundle adslOverISDN(3) indicates ADSL service over ISDN is present in the bundle" DEFVAL { none } ::= { vdslLineConfProfileEntry 29 } vdslLineConfApplicableStandard OBJECT-TYPE SYNTAX INTEGER { ansi(1), etsi(2), itu(3), other(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The VDSL standard to be used for the line. ansi(1) indicates ANSI standard etsi(2) indicates ETSI standard itu(3) indicates ITU standard other(4) indicates a standard other than the above." DEFVAL { ansi } ::= { vdslLineConfProfileEntry 30 } vdslLineConfBandPlan OBJECT-TYPE SYNTAX INTEGER { bandPlan997(1), bandPlan998(2), bandPlanFx(3), other(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The VDSL band plan to be used for the line. bandPlan997(1) is to be used for ITU-T G.993.1 Bandplan-B ETSI Bandplan ANSI Plan 997 bandPlan998(2) is to be used for ITU-T G.993.1 Bandplan-A ANSI Plan 998 bandPlanFx(3) is to be used for ITU-T G.993.1 Bandplan-C. other(4) is to be used for non-standard bandplans. If this object is set to bandPlanFx(3), then the object vdslLineConfBandPlanFx MUST also be set." DEFVAL { bandPlan997 } ::= { vdslLineConfProfileEntry 31 } vdslLineConfBandPlanFx OBJECT-TYPE SYNTAX Unsigned32 (3750..12000) UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "The frequency limit between bands D2 and U2 when vdslLineConfBandPlan is set to bandPlanFx(3)." DEFVAL { 3750 } ::= { vdslLineConfProfileEntry 32 } vdslLineConfBandOptUsage OBJECT-TYPE SYNTAX INTEGER { unused(1), upstream(2), downstream(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). unused(1) indicates Opt is unused upstream(2) indicates Opt usage is for upstream downstream(3) indicates Opt usage is for downstream." REFERENCE "ITU-T G.993.1, section 6.1" DEFVAL { unused } ::= { vdslLineConfProfileEntry 33 } vdslLineConfUpPsdTemplate OBJECT-TYPE SYNTAX INTEGER { templateMask1(1), templateMask2(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The upstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard)." REFERENCE "DSL TR-057" DEFVAL { templateMask1 } ::= { vdslLineConfProfileEntry 34 } vdslLineConfDownPsdTemplate OBJECT-TYPE SYNTAX INTEGER { templateMask1(1), templateMask2(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The downstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard)." REFERENCE "DSL TR-057" DEFVAL { templateMask1 } ::= { vdslLineConfProfileEntry 35 } vdslLineConfHamBandMask OBJECT-TYPE SYNTAX BITS { customNotch1(0), -- custom (region-specific) notch customNotch2(1), -- custom (region-specific) notch amateurBand30m(2), -- amateur radio band notch amateurBand40m(3), -- amateur radio band notch amateurBand80m(4), -- amateur radio band notch amateurBand160m(5) -- amateur radio band notch } MAX-ACCESS read-create STATUS current DESCRIPTION "The transmit power spectral density mask code, used to avoid interference with HAM (Handheld Amateur Radio) radio bands by introducing power control (notching) in one or more of these bands. Amateur radio band notching is defined in the VDSL spectrum as follows: Band Start Frequency Stop Frequency ---- ------------------ -------------------------------- 30m 1810 kHz 2000 kHz 40m 3500 kHz 3800 kHz (ETSI); 4000 kHz (ANSI) 80m 7000 kHz 7100 kHz (ETSI); 7300 kHz (ANSI) 160m 10100 kHz 10150 kHz Notching for each standard band can be enabled or disabled via the bit mask. Two custom notches may be specified. If either of these are enabled via the bit mask, then the following objects MUST be specified: If customNotch1 is enabled, then both vdslLineConfCustomNotch1Start vdslLineConfCustomNotch1Stop MUST be specified. If customNotch2 is enabled, then both vdslLineConfCustomNotch2Start vdslLineConfCustomNotch2Stop MUST be specified." REFERENCE "DSLF TR-057, section 2.6" DEFVAL { { } } ::= { vdslLineConfProfileEntry 36 } vdslLineConfCustomNotch1Start OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch 1. vdslLineConfCustomNotch1Start MUST be less than or equal to vdslLineConfCustomNotch1Stop." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 37 } vdslLineConfCustomNotch1Stop OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 1. vdslLineConfCustomNotch1Stop MUST be greater than or equal to vdslLineConfCustomNotch1Start." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 38 } vdslLineConfCustomNotch2Start OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch 2. vdslLineConfCustomNotch2Start MUST be less than or equal to vdslLineConfCustomNotch2Stop." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 39 } vdslLineConfCustomNotch2Stop OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 2. vdslLineConfCustomNotch2Stop MUST be greater than or equal to vdslLineConfCustomNotch2Start." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 40 } vdslLineConfDownTargetSlowBurst OBJECT-TYPE SYNTAX Unsigned32 (0..1275) UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the target level of impulse noise (burst) protection for an interleaved (slow) channel." REFERENCE "ITU-T G.997.1, section 7.3.2.3" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 41 } vdslLineConfUpTargetSlowBurst OBJECT-TYPE SYNTAX Unsigned32 (0..1275) UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the target level of impulse noise (burst) protection for an interleaved (slow) channel." REFERENCE "ITU-T G.997.1, section 7.3.2.3" DEFVAL { 0 } ::= { vdslLineConfProfileEntry 42 } vdslLineConfDownMaxFastFec OBJECT-TYPE SYNTAX Unsigned32 (0..50) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 43 } vdslLineConfUpMaxFastFec OBJECT-TYPE SYNTAX Unsigned32 (0..50) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel." DEFVAL { 0 } ::= { vdslLineConfProfileEntry 44 } vdslLineConfLineType OBJECT-TYPE SYNTAX INTEGER { noChannel(1), -- no channels exist fastOnly(2), -- only fast channel exists interleavedOnly(3), -- only interleaved channel exists fastOrInterleaved(4), -- either fast or interleaved channel -- exist, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist } MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter provisions the VDSL physical entity at start-up by defining whether and how the line will be channelized, i.e., which channel type(s) are supported. If the line is to be channelized, the value will be other than noChannel(1). This configuration can be activated only during start-up. Afterwards, the value of vdslLineType coincides with the value of vdslLineConfLineType. Depending on this value, the corresponding entries in the ifTable for the interleaved and the fast channels are enabled or disabled according to the value of their ifOperStatus. Defined values are: noChannel(1) -- no channels exist fastOnly(2) -- only fast channel exists interleavedOnly(3) -- only interleaved channel exists fastOrInterleaved(4) -- either fast or interleaved channel -- exists, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist Note that 'slow' and 'interleaved' refer to the same channel." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { noChannel } ::= { vdslLineConfProfileEntry 45 } vdslLineConfProfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time. Note that some changes may require that any referenced lines be restarted (e.g., vdslLineConfLineType)." ::= { vdslLineConfProfileEntry 46 } -- -- Alarm configuration profile table -- vdslLineAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the VDSL line alarm configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line alarm thresholds. Entries in this table MUST be maintained in a persistent manner." ::= { vdslMibObjects 20 } vdslLineAlarmConfProfileEntry OBJECT-TYPE SYNTAX VdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of a VDSL line alarm profile. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document." INDEX { vdslLineAlarmConfProfileName } ::= { vdslLineAlarmConfProfileTable 1 } VdslLineAlarmConfProfileEntry ::= SEQUENCE { vdslLineAlarmConfProfileName SnmpAdminString, vdslLineAlarmConfThresh15MinLofs HCPerfIntervalThreshold, vdslLineAlarmConfThresh15MinLoss HCPerfIntervalThreshold, vdslLineAlarmConfThresh15MinLprs HCPerfIntervalThreshold, vdslLineAlarmConfThresh15MinLols HCPerfIntervalThreshold, vdslLineAlarmConfThresh15MinESs HCPerfIntervalThreshold, vdslLineAlarmConfThresh15MinSESs HCPerfIntervalThreshold, vdslLineAlarmConfThresh15MinUASs HCPerfIntervalThreshold, vdslLineAlarmConfInitFailure TruthValue, vdslLineAlarmConfProfRowStatus RowStatus } vdslLineAlarmConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name for this profile as specified by an administrator." ::= { vdslLineAlarmConfProfileEntry 1 } vdslLineAlarmConfThresh15MinLofs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of frame seconds (lofs) within any given 15-minute performance data collection interval. If the value of loss of frame seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLofsThreshNotification notification will be generated. No more than one notification will be sent per interval." DEFVAL { 0 } ::= { vdslLineAlarmConfProfileEntry 2 } vdslLineAlarmConfThresh15MinLoss OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of signal seconds (loss) within any given 15-minute performance data collection interval. If the value of loss of signal seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLossThreshNotification notification will be generated. One notification will be sent per interval per endpoint." DEFVAL { 0 } ::= { vdslLineAlarmConfProfileEntry 3 } vdslLineAlarmConfThresh15MinLprs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of power seconds (lprs) within any given 15-minute performance data collection interval. If the value of loss of power seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLprsThreshNotification notification will be generated. No more than one notification will be sent per interval." DEFVAL { 0 } ::= { vdslLineAlarmConfProfileEntry 4 } vdslLineAlarmConfThresh15MinLols OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of link seconds (lols) within any given 15-minute performance data collection interval. If the value of loss of power seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLolsThreshNotification notification will be generated. No more than one notification will be sent per interval." DEFVAL { 0 } ::= { vdslLineAlarmConfProfileEntry 5 } vdslLineAlarmConfThresh15MinESs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of errored seconds (ESs) within any given 15-minute performance data collection interval. If the value of errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfESsThreshNotification notification will be generated. No more than one notification will be sent per interval." DEFVAL { 0 } ::= { vdslLineAlarmConfProfileEntry 6 } vdslLineAlarmConfThresh15MinSESs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of severely errored seconds (SESs) within any given 15-minute performance data collection interval. If the value of severely errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfSESsThreshNotification notification will be generated. No more than one notification will be sent per interval." DEFVAL { 0 } ::= { vdslLineAlarmConfProfileEntry 7 } vdslLineAlarmConfThresh15MinUASs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of unavailable seconds (UASs) within any given 15-minute performance data collection interval. If the value of unavailable seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfUASsThreshNotification notification will be generated. No more than one notification will be sent per interval." DEFVAL { 0 } ::= { vdslLineAlarmConfProfileEntry 8 } vdslLineAlarmConfInitFailure OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies if a vdslInitFailureNotification notification will be generated if an initialization failure occurs." DEFVAL { false } ::= { vdslLineAlarmConfProfileEntry 9 } vdslLineAlarmConfProfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to 'destroy' or 'outOfService') it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time." ::= { vdslLineAlarmConfProfileEntry 10 } -- Notification definitions vdslNotifications OBJECT IDENTIFIER ::= { vdslLineMib 0 } vdslPerfLofsThreshNotification NOTIFICATION-TYPE OBJECTS { vdslPerfDataCurr15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold (vdslLineAlarmConfThresh15MinLofs) reached." ::= { vdslNotifications 1 } vdslPerfLossThreshNotification NOTIFICATION-TYPE OBJECTS { vdslPerfDataCurr15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold (vdslLineAlarmConfThresh15MinLoss) reached." ::= { vdslNotifications 2 } vdslPerfLprsThreshNotification NOTIFICATION-TYPE OBJECTS { vdslPerfDataCurr15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold (vdslLineAlarmConfThresh15MinLprs) reached." ::= { vdslNotifications 3 } vdslPerfLolsThreshNotification NOTIFICATION-TYPE OBJECTS { vdslPerfDataCurr15MinLols } STATUS current DESCRIPTION "Loss of Link 15-minute interval threshold (vdslLineAlarmConfThresh15MinLols) reached." ::= { vdslNotifications 4 } vdslPerfESsThreshNotification NOTIFICATION-TYPE OBJECTS { vdslPerfDataCurr15MinESs } STATUS current DESCRIPTION "Errored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinESs) reached." ::= { vdslNotifications 5 } vdslPerfSESsThreshNotification NOTIFICATION-TYPE OBJECTS { vdslPerfDataCurr15MinSESs } STATUS current DESCRIPTION "Severely Errored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinSESs) reached." ::= { vdslNotifications 6 } vdslPerfUASsThreshNotification NOTIFICATION-TYPE OBJECTS { vdslPerfDataCurr15MinUASs } STATUS current DESCRIPTION "Unavailable Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinUASs) reached." ::= { vdslNotifications 7 } vdslDownMaxSnrMgnNotification NOTIFICATION-TYPE OBJECTS { vdslPhysCurrSnrMgn } STATUS current DESCRIPTION "The downstream Signal to Noise Margin exceeded vdslLineConfDownMaxSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-R." ::= { vdslNotifications 8 } vdslDownMinSnrMgnNotification NOTIFICATION-TYPE OBJECTS { vdslPhysCurrSnrMgn } STATUS current DESCRIPTION "The downstream Signal to Noise Margin fell below vdslLineConfDownMinSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-R." ::= { vdslNotifications 9 } vdslUpMaxSnrMgnNotification NOTIFICATION-TYPE OBJECTS { vdslPhysCurrSnrMgn } STATUS current DESCRIPTION "The upstream Signal to Noise Margin exceeded vdslLineConfUpMaxSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-C." ::= { vdslNotifications 10 } vdslUpMinSnrMgnNotification NOTIFICATION-TYPE OBJECTS { vdslPhysCurrSnrMgn } STATUS current DESCRIPTION "The upstream Signal to Noise Margin fell below vdslLineConfUpMinSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-C." ::= { vdslNotifications 11 } vdslInitFailureNotification NOTIFICATION-TYPE OBJECTS { vdslPhysCurrStatus } STATUS current DESCRIPTION "Vtu initialization failed. See vdslPhysCurrStatus for potential reasons." ::= { vdslNotifications 12 } -- conformance information vdslConformance OBJECT IDENTIFIER ::= { vdslLineMib 3 } vdslGroups OBJECT IDENTIFIER ::= { vdslConformance 1 } vdslCompliances OBJECT IDENTIFIER ::= { vdslConformance 2 } vdslLineMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which manage VDSL interfaces." MODULE -- this module MANDATORY-GROUPS { vdslGroup, vdslNotificationGroup } ::= { vdslCompliances 1 } -- units of conformance vdslGroup OBJECT-GROUP OBJECTS { vdslLineCoding, vdslLineType, vdslLineConfProfile, vdslLineAlarmConfProfile, vdslPhysInvSerialNumber, vdslPhysInvVendorID, vdslPhysInvVersionNumber, vdslPhysCurrSnrMgn, vdslPhysCurrAtn, vdslPhysCurrStatus, vdslPhysCurrOutputPwr, vdslPhysCurrAttainableRate, vdslPhysCurrLineRate, vdslChanInterleaveDelay, vdslChanCrcBlockLength, vdslChanCurrTxRate, vdslChanCurrTxSlowBurstProtect, vdslChanCurrTxFastFec, vdslPerfDataValidIntervals, vdslPerfDataInvalidIntervals, vdslPerfDataLofs, vdslPerfDataLoss, vdslPerfDataLprs, vdslPerfDataLols, vdslPerfDataESs, vdslPerfDataSESs, vdslPerfDataUASs, vdslPerfDataInits, vdslPerfDataCurr15MinTimeElapsed, vdslPerfDataCurr15MinLofs, vdslPerfDataCurr15MinLoss, vdslPerfDataCurr15MinLprs, vdslPerfDataCurr15MinLols, vdslPerfDataCurr15MinESs, vdslPerfDataCurr15MinSESs, vdslPerfDataCurr15MinUASs, vdslPerfDataCurr15MinInits, vdslPerfData1DayValidIntervals, vdslPerfData1DayInvalidIntervals, vdslPerfDataCurr1DayTimeElapsed, vdslPerfDataCurr1DayLofs, vdslPerfDataCurr1DayLoss, vdslPerfDataCurr1DayLprs, vdslPerfDataCurr1DayLols, vdslPerfDataCurr1DayESs, vdslPerfDataCurr1DaySESs, vdslPerfDataCurr1DayUASs, vdslPerfDataCurr1DayInits, vdslPerfIntervalLofs, vdslPerfIntervalLoss, vdslPerfIntervalLprs, vdslPerfIntervalLols, vdslPerfIntervalESs, vdslPerfIntervalSESs, vdslPerfIntervalUASs, vdslPerfIntervalInits, vdslPerf1DayIntervalMoniSecs, vdslPerf1DayIntervalLofs, vdslPerf1DayIntervalLoss, vdslPerf1DayIntervalLprs, vdslPerf1DayIntervalLols, vdslPerf1DayIntervalESs, vdslPerf1DayIntervalSESs, vdslPerf1DayIntervalUASs, vdslPerf1DayIntervalInits, vdslChanValidIntervals, vdslChanInvalidIntervals, vdslChanFixedOctets, vdslChanBadBlks, vdslChanCurr15MinTimeElapsed, vdslChanCurr15MinFixedOctets, vdslChanCurr15MinBadBlks, vdslChan1DayValidIntervals, vdslChan1DayInvalidIntervals, vdslChanCurr1DayTimeElapsed, vdslChanCurr1DayFixedOctets, vdslChanCurr1DayBadBlks, vdslChanIntervalFixedOctets, vdslChanIntervalBadBlks, vdslChan1DayIntervalMoniSecs, vdslChan1DayIntervalFixedOctets, vdslChan1DayIntervalBadBlks, vdslLineConfDownRateMode, vdslLineConfUpRateMode, vdslLineConfDownMaxPwr, vdslLineConfUpMaxPwr, vdslLineConfDownMaxSnrMgn, vdslLineConfDownMinSnrMgn, vdslLineConfDownTargetSnrMgn, vdslLineConfUpMaxSnrMgn, vdslLineConfUpMinSnrMgn, vdslLineConfUpTargetSnrMgn, vdslLineConfDownFastMaxDataRate, vdslLineConfDownFastMinDataRate, vdslLineConfDownSlowMaxDataRate, vdslLineConfDownSlowMinDataRate, vdslLineConfUpFastMaxDataRate, vdslLineConfUpFastMinDataRate, vdslLineConfUpSlowMaxDataRate, vdslLineConfUpSlowMinDataRate, vdslLineConfDownRateRatio, vdslLineConfUpRateRatio, vdslLineConfDownMaxInterDelay, vdslLineConfUpMaxInterDelay, vdslLineConfDownPboControl, vdslLineConfUpPboControl, vdslLineConfDownPboLevel, vdslLineConfUpPboLevel, vdslLineConfDeploymentScenario, vdslLineConfAdslPresence, vdslLineConfApplicableStandard, vdslLineConfBandPlan, vdslLineConfBandPlanFx, vdslLineConfBandOptUsage, vdslLineConfUpPsdTemplate, vdslLineConfDownPsdTemplate, vdslLineConfHamBandMask, vdslLineConfCustomNotch1Start, vdslLineConfCustomNotch1Stop, vdslLineConfCustomNotch2Start, vdslLineConfCustomNotch2Stop, vdslLineConfDownTargetSlowBurst, vdslLineConfUpTargetSlowBurst, vdslLineConfDownMaxFastFec, vdslLineConfUpMaxFastFec, vdslLineConfLineType, vdslLineConfProfRowStatus, vdslLineAlarmConfThresh15MinLofs, vdslLineAlarmConfThresh15MinLoss, vdslLineAlarmConfThresh15MinLprs, vdslLineAlarmConfThresh15MinLols, vdslLineAlarmConfThresh15MinESs, vdslLineAlarmConfThresh15MinSESs, vdslLineAlarmConfThresh15MinUASs, vdslLineAlarmConfInitFailure, vdslLineAlarmConfProfRowStatus } STATUS current DESCRIPTION "A collection of objects providing information about a VDSL Line." ::= { vdslGroups 1 } vdslNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { vdslPerfLofsThreshNotification, vdslPerfLossThreshNotification, vdslPerfLprsThreshNotification, vdslPerfLolsThreshNotification, vdslPerfESsThreshNotification, vdslPerfSESsThreshNotification, vdslPerfUASsThreshNotification, vdslDownMaxSnrMgnNotification, vdslDownMinSnrMgnNotification, vdslUpMaxSnrMgnNotification, vdslUpMinSnrMgnNotification, vdslInitFailureNotification } STATUS current DESCRIPTION "This group supports notifications of significant conditions associated with VDSL Lines." ::= { vdslGroups 2 } END 5. Security Considerations There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. VDSL layer connectivity from the Vtur will permit the subscriber to manipulate both the VDSL link directly and the VDSL embedded operations channel (EOC) for their own loop. For example, unchecked or unfiltered fluctuations initiated by the subscriber could generate sufficient notifications to potentially overwhelm either the management interface to the network or the element manager. Additionally, allowing write access to configuration data may allow an end-user to increase their service levels or affect other end- users in either a positive or negative manner. For this reason, the following tables should be considered to contain sensitive information: - vdslLineTable - vdslLineConfProfileTable - vdslLineAlarmConfProfileTable Individual line utilization information, available via the performance tables, may be considered sensitive. For example, if an end-user has a far lower line utilization during certain periods of the day, it may indicate an empty office or residence. For these reasons, the following tables should be considered to contain sensitive information: - vdslPerfDataTable - vdslPerfIntervalTable - vdslPerf1DayIntervalTable Further, notifications generated by agents implementing this MIB will contain threshold and performance information. It is thus important to control even GET access to the objects within these tables and possibly to even encrypt the values of these objects when sending them over the network via SNMP. Not all versions of SNMP provide features for such a secure environment. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 6. References 6.1. Normative References [DSLFTR057] DSL Forum TR-057, "VDSL Network Element Management", February 2003. [ETSI2701] ETSI TS 101 270-1 V1.2.1 "Transmission and Multiplexing (TM); Access transmission systems on metallic access cables; Very high speed Digital Subscriber Line (VDSL); Part 1: Functional requirements", October 1999. [ETSI2702] ETSI TS 101 270-2 V1.1.1 "Transmission and Multiplexing (TM); Access transmission systems on metallic access cables; Very high speed Digital Subscriber Line (VDSL); Part 1: Transceiver specification", February 2001. [ITU9931] ITU-T G.993.1 "Very-high-speed digital subscriber line foundation", November 2001. [ITU9971] ITU-T G.997.1 "Physical layer management for Digital Subscriber Line (DSL) Transceivers", July 1999. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC2856] Bierman, A., McCloghrie, K. and R. Presuhn, "Textual Conventions for Additional High Capacity Data Types", RFC 2856, June 2000. [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [RFC3411] Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", RFC 3411, December 2002. [RFC3418] Presuhn, R., "Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)", STD 62, RFC 3418, December 2002. [RFC3593] Tesink, K., "Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 3593, September 2003. [RFC3705] Ray, B. and R. Abbi, "High Capacity Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 3705, February 2004. [T1E1311] ANSI T1E1.4/2001-311, "Very-high-bit-rate Digital Subscriber Line (VDSL) Metallic Interface, Part 1: Functional Requirements and Common Specification", February 2001. [T1E1011] ANSI T1E1.4/2001-011R3, "VDSL Metallic Interface, Part 2: Technical Specification for a Single-Carrier Modulation (SCM) Transceiver", November 2001. [T1E1013] ANSI T1E1.4/2001-013R4, "VDSL Metallic Interface, Part 3: Technical Specification for a Multi-Carrier Modulation (MCM) Transceiver", November 2000. 6.2. Informative References [RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, December 2002. [RFC3415] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", STD 62, RFC 3415, December 2002. 7. Acknowledgements Greg Bathrick (Texas Instruments) Umberto Bonollo (NEC) Andrew Cheers (NEC) Felix Flemisch (Siemens) David Horton (CiTR) Travis Levin (Paradyne) Moti Morgenstern (Inovia) Randy Presuhn (BMC) Say Sabit (NLC) Bert Wijnen (Lucent) 8. Authors' Addresses Bob Ray PESA Switching Systems, Inc. 330-A Wynn Drive Huntsville, AL 35805 USA Phone: +1 256 726 9200 ext. 142 Fax: +1 256 726 9271 EMail: rray@pesa.com Rajesh Abbi Alcatel USA 2301 Sugar Bush Road Raleigh, NC 27612-3339 USA Phone: +1 919 850 6194 EMail: Rajesh.Abbi@alcatel.com 9. Full Copyright Statement Copyright (C) The Internet Society (2004). This document is subject to the rights, licenses and restrictions contained in BCP 78 and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf- ipr@ietf.org. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society.